Terra Universal BioSafe+ Smart Pass-Through Скачать руководство пользователя страница 3

Страница: 3 / 16

Installation and Operating Guide

Smart Pass-Through Chambers

Terra Universal, Inc. • TerraUniversal.com • 800 S. Raymond Ave. • Fullerton, CA 92831 • TEL: (714) 578-6000 • FAX: (714) 578-6020

Proprietary Notice

Safety Notice

This manual pertains to proprietary devices manufactured by

Terra Universal, Inc. Neither this document nor any portion of

it may be reproduced in any way without prior written

permission from Terra Universal.

A thorough familiarity with all operating guidelines is essential to safe

operation of the product. Failure to observe safety precautions could

result in poor performance, damage to the system or other property, or

serious bodily injury or death. The following symbols are intended to call

your attention to two levels of hazard involved in operation.

Terra Universal makes no warranties applying to information

contained in this manual or its suitability for any implied or

inferred purpose. Terra Universal shall not be held liable for

any errors this manual contains or for any damages that

result from its use.

CAUTION

Cautions are used when failure to observe instructions could

result in significant damage to equipment.

WARNING

Warnings are used when failure to observe instructions or

precautions could result in injury or death.

The information presented here is subject to change without notice.

Description

1.0

The installation and operating instructions in this manual apply to both the standard Smart Pass-Through and the

Smart Pass-Through, which features a non-outgassing, potted polyurethane door seal. The standard model uses an “e”-

shaped, heat-formed gasket to seal the doors.
The Smart Pass-Through series includes an electronic interlock which allows only one open door at a time, thus minimizing the

amount of “dirty” air that can enter the cleanroom. This interlock system is operated by an integral Smart Controller, which

features indicator lights and alarm bells as standard equipment. The Smart controller can also be equipped with any number of

Smart Pass-through™ accessory modules, expanding its capabilities to include UV sterilization, air showers, load presence

sensors, data-logging, and a host of high-tech security features.

The operator should always verify the opposite door is fully shut prior to opening a door. Do not yank,

shake, or apply excessive force to the doors. Attempting to force open a door while the interlock is

engaged may result in damage to the unit.

CAUTION

Smart Door Interlock™

Terra Universal’s Smart Pass-Through™ chambers are equipped with electronic interlocks to

prevent the opening of both doors simultaneously. When one door is open, the other will remain

locked until both doors have been closed.

This cross-contamination protection is accomplished using an internal Smart Pass-through

Controller built into the body of the pass-through chamber. The unit arrives from the factory pre-

programmed to control the door interlock system, alarm bells, and any Smart Pass-through™

accessories specified in the order.

Figure 1:

Smart Pass-Through

with slide-up door

Содержание BioSafe+ Smart Pass-Through

















Результаты поиска

Содержание BioSafe+ Smart Pass-Through

Отзывы:

Бренды по названию

Популярные бренды

Terra Universal BioSafe+ Smart Pass-Through, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BioSafe+ Smart Pass-Through

Отзывы:

Бренды по названию

Популярные бренды