TERASAKI TemTransfer 2 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 45

background image

Installation

14

4.1.7 PC CONFIGURATION INTERFACE CONNECTOR

DESCRIPTION

CABLE

SIZE

NOTES

Socket for connection to PC with
Configuration Suite PC software.

0.5mm²

AWG 20

This is a standard USB type A to

type B cable.

NOTE:- The USB connection cable between the PC and the TemTransfer 2 module must not be

extended beyond 5m (5yds). For distances over 5m, it is possible to use a third party USB extender.
Typically, they extend USB up to 50m (yds). The supply and support of this type of equipment is outside
the scope of Terasaki.

CAUTION!: Care must be taken not to overload the PCs USB system by connecting more than the

recommended number of USB devices to the PC. For further information, consult your PC supplier.

CAUTION!: This socket must not be used for any other purpose.

This configuration cable is
the same as normally used
between a PC and a USB
printer.

«
...
12
13
14
15
16
...
»

Содержание TemTransfer 2














































Отзывы:

Нет отзывов

Похожие инструкции для TemTransfer 2

Бренд: GBD Страницы: 12

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: Jabra Страницы: 3

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: Mamas & Papas Страницы: 24

Бренд: Mamas & Papas Страницы: 24

Бренд: UNISENSE Страницы: 16

Бренд: Xylem Страницы: 48

Бренд: Gardena Страницы: 236

Бренд: Paradox Страницы: 6

Бренд: 2gig Technologies Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды