Tennant 235D Скачать руководство пользователя страница 46

Страница: 46 / 203

MAINTENANCE

235 MM331 (3--93)

3-10

8. Replace the engine coil wire.

9. Start the engine and operate it at an idle for

two minutes.

10. Press the directional pedal one-half of its

travel in the “forward”direction while also

operating the main brush and side brush for

one minute.

11. Adjust the directional pedal as described in

TO ADJUST DIRECTIONAL PEDAL

LINKAGE

12. Stop the engine.

13. Raise the rear of the machine, remove the

jack stands, and lower the machine.

14. Fill the hydraulic fluid reservoir with new,

approved hydraulic fluid.

15. Check the hose routings to be sure the

hoses do not contact any moving, hot, or

sharp surfaces.

16. Replace the hydraulic fluid filter after the first

hour of operation.

DIRECTIONAL PEDAL

The directional pedal controls the flow of hydraulic

fluid to the hydraulic drive motor. The pedal has

three positions -- ”forward,”“neutral,”and

“reverse.”The “forward”and “reverse”positions

send hydraulic fluid to the drive motor to propel

the machine.

The “neutral”position is the position in which the

propelling pump sends no hydraulic fluid to the

propelling motor. The machine should not creep

when the “neutral”position is correctly adjusted.

Adjust the pedal linkages, as described in

TO ADJUST DIRECTIONAL PEDAL LINKAGE

whenever the machine creeps or after replacing

the hydraulic propelling pump or pump linkages.

The pedal linkages should also be adjusted

whenever the reverse speed is excessive or

inadequate.

TO ADJUST DIRECTIONAL PEDAL LINKAGE

1. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

2. Block the machine tires and jack up the rear

of the machine at the designated location.

FOR SAFETY: When Servicing Machine, Block

Machine Tires Before Jacking Machine Up.

3. Block up the machine with jack stands in the

designated locations. Make sure the rear tire

clears the floor by 2 in (50 mm) and all

obstacles within a 24 in (610 mm) radius.

FOR SAFETY: When Servicing Machine, Jack

Machine Up At Designated Locations Only.

Block Machine Up With Jack Stands.

4. Loosen the two centering bolts jam nuts.

03505

CENTERING BOLTS

A. Adjustment Bolts

B. Pintle Arm

C. Centering Stop

Содержание 235D












































































































































































































Результаты поиска

Содержание 235D

Отзывы:

Похожие инструкции для 235D

Бренды по названию

Популярные бренды

Tennant 235D, Руководство пользователя

Результаты поиска

Содержание 235D

Отзывы:

Похожие инструкции для 235D

Бренды по названию

Популярные бренды