manualshive.com logo in svg

Tennant 140, Руководство оператора и каталог запасных частей, Страница: 17 / 104

Поделиться
Скачать
Tennant 140 Скачать руководство пользователя страница 17

OPERATION

2-7

140 MM130 (6--91)

MACHINE OPERATION

NORMAL SWEEPING OPERATION

A normal sweeping operation consists of seven

typical operations: pre-start checklist, starting

machine, sweeping, dumping hopper, post

operation checklist-engine operating, stopping

machine, and post operation checklist--engine

stopped.

THE PRE-START CHECKLIST

lists things to

check before starting the machine.

TO START MACHINE

lists the steps required to

start the machine.

TO SWEEP

lists things to keep in mind before

and during the sweeping operation.

TO DUMP HOPPER

lists the steps required to

dump the hopper.

POST OPERATION CHECKLIST

-- Engine

Operating lists things to check before stopping the

machine engine.

TO STOP MACHINE

lists the steps required to

stop the machine.

POST OPERATION CHECKLIST

-- Engine

Stopped lists things to check after stopping the

machine engine.

PRE-START CHECKLIST
Check under machine for leak spots.

Check engine lubricating oil level.

Check fuel level.

Check controls for proper operation.

Check service records to determine service

requirements.

FOR SAFETY: Before Starting Machine; Check

For Fuel Leaks, Keep Sparks And Open Flame

Away From Refueling Area, And Make Sure All

Safety Devices Are In Place And Operate

Properly.

TO START MACHINE

NOTE: Before starting machine, perform the

pre-start checks.

1. Close the choke if the engine is cold.

2. Pull the engine starter cord to start the

engine.

3. Drive the machine to the area to be cleaned.

TO SWEEP
Plan the sweeping in advance. Try to arrange long

runs with minimum stopping and starting. Sweep

debris from very narrow aisles into main aisles

ahead of time. Do an entire floor or section at one

time. Overlap brush paths.

Pick up oversize debris before sweeping. Flatten

or remove bulky cartons from aisles before

sweeping. Pick up pieces of wire, twine, string,

etc., which could become entangled in brush or

brush plugs.

Press the clutch handle to place the machine in

motion. Release the clutch handle for easier

turning. Sweep as straight a path as possible.

Avoid bumping into posts or scraping the sides of

the sweeper. Empty the debris hopper when it

becomes full.

1. Place the main brush lift handle in the

“lower” position.

2. Pull the side brush arm up, forward and

down into the “operating” position if present.

3. Sweep as required.

NOTE: Do not allow the machine to remain

stationary with machine operating and the main

brush in the “lower” position as it may cause wear

marks on the floor.

Содержание 140









































































































Отзывы:

Нет отзывов