Tenma 72-8150 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 26

Tenma 72-8150 Скачать руководство пользователя страница 24

To avoid injury due to electrical shock or arc blast,
and to avoid damage to the Meter, use specified fuses
ONLY in accordance with the following procedure.

Warning

To replace the Meter’s fuse:

Turn the Meter power off and remove all connections
from the terminals.
Remove the screw from the battery compartment, and
separate the battery compartment from the case bottom.
Remove the screws from the case bottom, and separate
the case top from the case bottom.
Remove the fuse by gently prying one end loose, then
take out the fuse from its bracket.
Install ONLY replacement fuses with the identical type
and specification as follows and make sure the fuse is
fixed firmly in the bracket.
Fuse 1: 0.315A, 250V, fast type fuse, 5x20 mm.
Replace the battery compartment and the case top, and
reinstall the screw.
Replace the case bottom and case top, and reinstall the
screws.

1.

2.

3.

4.

5.

6.

7.

24

C. Replacing the Fuse

(see figure 8)

(figure 8)

SCREW

Model 72-8150: OPERATING MANUAL

«
...
22
23
24
25
26
»

Содержание 72-8150



























Отзывы:

Нет отзывов