Tenma 72-7740 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 35

background image

The POWER button

This is a self-lock switch used to turn on or off the power of the
Meter.

The BLUE button

It is used for selecting the required measurement function when
more than one function exists at one position of the rotary
switch.

Turning on the Display Backlight

In order to avoid the hazard arising from mistaken readings
in insufficient light or poor vision, please use Display
Backlight function.

l

Press and hold HOLD H for over 2 seconds to turn the
Display Backlight on.

l

Press and hold HOLD H again for over 2 seconds to turn the
Display Backlight off, otherwise it will stay on continuously.

Sleep Mode (Model 72-7740)

To preserve battery life, the Meter automatically turns off after

30 minutes of inactivity.

To disable the Sleep Mode function, press BLUE button while
turning on the Meter.

Warning

25

Model 72-7740/72-7745: OPERATING MANUAL

«
...
23
24
25
26
27
...
»

Содержание 72-7740




































Отзывы:

Нет отзывов

Похожие инструкции для 72-7740

Бренд: AEMC Страницы: 8

Бренд: Omega Страницы: 15

Бренд: American Fibertek Страницы: 10

Бренд: Tenma Страницы: 8

Бренд: Tenma Страницы: 12

Бренд: Tenma Страницы: 11

Бренд: Tenma Страницы: 17

Бренд: NIMEX Страницы: 12

Бренд: Orion Страницы: 35

Бренд: DANA Страницы: 149

Бренд: VOLTCRAFT Страницы: 90

Бренд: Mastech Страницы: 8

HB74 Heavy Duty

Бренд: Fieldpiece Страницы: 16

Бренд: Maxwell Digital Multimeters Страницы: 24

Бренд: Maxwell Digital Multimeters Страницы: 32

Бренд: ETEKCITY Страницы: 16

Бренд: YATO Страницы: 40

Бренд: Magnescale Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды