Ten-Haaft Premium OYSTER 65, Инструкция по эксплуатации, Страница: 2 / 27

2 3
CONTENTS
1. Control elements
1.1 Getting started / switching the system on and off 3
1.2 Operating the antenna 4
1.3 Remote control 5
1.4 Interfaces / control elements at device (19", 21.5", 23.6") 8
1.5 Interfaces / control elements at device (32") 10
2. Operating the system
2.1 Switching the system on / off 14
2.2 Button functions 15
2.3 ten Haaft® app 16
3. Operating the "Oyster® TV"
3.1 Initial setup 19
3.2 General TV settings 20
3.3 Channel settings and search (DVB-T / T2) 24
3.4 Channel settings and search (DVB-S / S2) 27
3.5 Favourites list (satellite TV) 32
3.6 Recording with the "Oyster® TV" 32
3.7 Further functions 37
3.8 Technical data of "Oyster
®
TV" 41
4. Service
4.1 Reception in practice – aiming the satellite system 42
4.2 Reception in remote areas 43
4.3 Notification tones / warning tones 46
4.4 Troubleshooting 47
4.5 Command Unit update via USB stick 48
1. CONTROL ELEMENTS
1.1 Getting started / switching the system on and off
The only control elements of the fully automatic satellite system "Oyster® TV" Premium are the receiver integrat-
ed in the "Oyster® TV" Premium system and the remote control. The remote control buttons are only operational
when the "Oyster® TV" Premium system is switched on and the initialisation has been completed. Your system
can also be operated via the ten Haaft® app (see page 16, point 2.3, "ten Haaft® app").
SWITCHING THE SYSTEM ON / OFF
The system is switched into standby mode or completely off at the switch on the underside of the "Oyster® TV"
Premium system (see page 8, element 12 or page 10, element 10). Operation is started by pressing the POWER
button on the remote control.
Caution!
When switching on the "Oyster® TV" Premium system, the antenna will start the automatic satellite search. The
receiver integrated in the Oyster® TV" Premium system needs up to one minute to initialise after being switched
on. The antenna then folds up and starts the automatic satellite search.
Note:
Unless specified otherwise, all information refers to the buttons of the remote control.
Caution!
When switching on the "Oyster® TV" Premium with integrated receiver, the antenna will unfold and start the
automatic satellite search.
1. Operate the switch on the side or underside of the device. The standby LED on the front illuminates red.
2. Press the POWER button on the remote control. The standby LED will illuminate blue.
SWITCHING THE DEVICE OFF
To switch the device into standby mode, press POWER. The standby LED will illuminate red. If you will not be
using the TV set for an extended period, you can turn it off at the switch on the side or underside. Note that the
system may first retract and then unfold to perform a satellite search when you switch it back on.
CONTROL PRIORITY OF AN "OYSTER® TV" SET USED IN A TWIN SYSTEM
If you have decided for a TWIN system with two "Oyster® TV" sets, the system can be controlled via the PRIMARY
"Oyster® TV" set only. In most cases, this will be the TV set in the living compartment of your recreational vehicle.
The secondary TV set cannot transfer any control commands to the antenna controller. Secondary TV sets are
usually located in the sleeping compartment.
You can also use your mobile device or tablet (IOS or Android) in combination with the ten Haaft® app on it at
any time to control and operate your system. See section 2.3 / page 16 in these instructions.
When controlling your Oyster® system via the app, the app’s commands take priority. This means that you can
retract or unfold the antenna or change to another satellite even when the primary TV set is turned off; the app
can operate the antenna even if the first TV set is switched off.
Be sure to observe the operating manual and installation instructions provided.