Tempstar C4A3 Скачать руководство пользователя страница 10

Страница: 10 / 18

INSTALLATION INSTRUCTIONS

−

410A Split System Air Conditioner

421 01 5103 00

ELECTRICAL WIRING

WARNING

ELECTRICAL SHOCK HAZARD
Failure to turn off the main (remote) electrical dis-

connect device could result in personal injury or

death.
Before installing, modifying or servicing system,

turn OFF the main (remote) electrical disconnect

device. There may be more than one disconnect

device.

The supply voltage must be 208/230 volts (197 volt

minimum to 253 volts maximum) 60 Hz single phase.
Outdoor units are approved for use with copper

conductors only. Do not use aluminum wire.
Refer to unit rating plate for minimum circuit ampacity

and circuit protection requirements.

Grounding

Permanently ground unit in accordance with the National

Electrical Code and local codes or ordinances. Use a

copper conductor of the correct size from the grounding

lug in control box to a grounded connection in the service

panel or a properly driven and electrically grounded

ground rod.

Wiring Connections

Make all outdoor electrical supply (Line Voltage)

connections with raintight conduit and fittings. Most

codes require a disconnect switch outdoors within sight

of the unit. Consult local codes for special requirements.
Route electrical supply (Line Voltage) wiring through

knockout hole in bottom of Control Box. Connect wires to

Contactor and Ground Lug according to Wiring Diagram

on unit. Refer to Figure 10.
Route thermostat wiring through rubber grommet in

bottom of Control Box. Low voltage lead wires are

provided in the control box for connection to thermostat

wires (use wire nuts). Refer to Wiring Diagram on unit

and Figure 11 for low voltage wiring examples.

NOTE:

Use No. 18 AWG (American Wire Gage)

color

−

coded, insulated (35

C minimum) wire. If

thermostat is located more than 100 feet (31 m) from unit

as measured along the control voltage wires, use No. 16

AWG color

−

coded wires to avoid excessive voltage

drop.

NOTE:

Some models are factory equipped with Comfort

Alert

Diagnostics device. If Comfort Alert is used as a

field installed option, then a hot bundle must be run for

proper connection.

Figure 10

Electrical Supply (Line Voltage) Connections

DISCONNECT

PER NEC AND/OR

LOCAL CODES

CONTACTOR

GROUND

LUG

FIELD GROUND

WIRING

FIELD POWER

WIRING

23 or 13

Содержание C4A3



















Результаты поиска

Содержание C4A3

Отзывы:

Бренды по названию

Популярные бренды

Tempstar C4A3, Руководство по установке

Результаты поиска

Содержание C4A3

Отзывы:

Бренды по названию

Популярные бренды