background image

English

 – 17

MAINTENANCE

Air filter

Air filters must be regularly cleaned to remove dust and dirt in 
order to avoid:

Carburettor malfunctions

Starting problems

Loss of engine power

Unnecessary wear to engine parts

Excessive fuel consumption.

The air filter system consists of an oiled foam plastic filter (1) 
and a paper filter (2):

1

The foam plastic filter is easily accessible under the filter 
cover A. This filter should be checked weekly and replaced 
if necessary. In order to obtain a good filtering effect, the 
filter must be replaced regularly or cleaned and oiled. A 
special HUSQVARNA oil has been produced for this 
purpose.

Remove the foam plastic filter. Wash the filter well in tepid 
soapy water. After cleaning, rinse the filter well in clean 
water. Squeeze out and allow the filter to dry. NOTE! High 
pressure compressed air can damage the foam.

Put the filter in a plastic bag and pour the filter oil over it. 
Knead the plastic bag to distribute the oil. Squeeze the 
excess oil out of the filter inside the plastic bag and pour 
off the excess before fitting the filter to the machine. Never 
use common engine oil. This would drain through the filter 
quite quickly and collect in the bottom.

2

The paper filter is accessible under cover B. This filter 
must be replaced/cleaned when the engine's power 
drops. The filter is cleaned by shaking. Note that the filter 
must not be washed. NOTE! High pressure compressed 
air can damage the filter.

An air filter that has been in use for a long time cannot be 
cleaned completely. The filter must therefore be replaced with 
a new one at regular intervals. 

A damaged air filter must 

always be replaced.

Starter

Changing a broken or worn starter cord

Loosen the filter and cylinder cover.

Loosen the screws that hold the starter against the 
crankcase and remove the starter.

Pull out the cord approx. 30 cm (12 inches) and hook it 
into the notch in the rim of the pulley. Release the recoil 
spring by letting the pulley rotate slowly backwards.

A

B

IMPORTANT INFORMATION

 Poor maintenance of the air 

filter will cause carbon build-up on the spark plug and 
abnormal wear to engine parts.

!

WARNING! When the recoil spring is wound 
up in the starter housing it is under tension 
and can, if handled carelessly, pop out and 
cause personal injury.

Always be careful when changing the recoil 
spring or the starter cord. Always wear 
protective goggles.

Содержание 396K
























Отзывы: