background image

3

Temco VF36RN/RNH/RP

78586

Important Information

INSTALLER: Please leave these instructions with the
owner.
OWNER:  Please retain these instructions for future
reference.
IMPORTANT: READ THESE INSTRUCTIONS CARE-
FULLY BEFORE OPERATING.

Use only with two-stage regulator.

DO NOT use this heater if any part of it has been under

water. Immediately call a qualified technician to inspect the
appliance and replace any part of the control system and any
gas control which has been under water.

This appliance may be installed in an after-market* manufac-

tured "mobile" home where not prohibited by state or local
codes.

*After-market:  Completion of sale, not for purpose of re-sale from the

manufacturer.

Children and adults should be alerted to the hazard of high

surface temperature and should stay away to avoid burns or
clothing ignition.

Although your gas logs are very realistic in appearance,

it is not a real wood-burning fireplace and must not be
used for burning solid fuel.

To avoid irreparable damage to the appliance or personal

injury; matches, paper, garbage or any other material must not
be placed or thrown on top of the logs or into the flames.

To avoid personal injury, do not touch hot surfaces when

the appliance is operating.

Close supervision is necessary when the appliance is

being operated near children.

Do not use to cook food.

This appliance is intended to be used only for supplemental

heat.  Do not use it routinely as a primary heat source.
Continuous operation could produce excessive humidity
depending on construction characteristics and outdoor tempera-
tures (below 20

°

F).  Over time, this could cause condensation

to form and damage wall structures and exterior paint.

An unvented room heater having an input rating of more than

10,000 btu per hour shall not be installed in a bedroom or
bathroom.

NOTES

Due to high temperatures, the appliance should be

located out of traffic and away from furniture and draper-
ies.

Installation and repair must be done by a qualified service

person or gas appliance installer.

A fireplace screen must be in place when the appliance is

operating.  On models with movable screens, the screens must
be closed when the fireplace is operating.

The appliance must be inspected before use and at least

annually by a professional service person. More frequent
cleaning may be required due to excessive lint from carpeting,
bedding material, dust and pet hair, etc. It is important that the
control compartment, burners and circulating air passageways
of the appliance be kept clean.

DO NOT place clothing or other flammable material on or

near the appliance.

This appliance must only be used with pressures at the inlet

as shown in Table 1, Page 11 in installation instructions.

The installation must conform with local codes or, in the

absence of local codes, with the NATIONAL FUEL GAS CODE,
ANSI Z223, latest edition.

Any safety screen or guard removed for servicing an appli-

ance must be replaced prior to operating the heater.

The appliance and its appliance main gas shut-off valve must

be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2 psig (3.5 kpa).

The appliance must be isolated from the gas supply piping

system by closing its equipment shut-off valve during any
testing of the gas supply piping system at test pressures equal
to or less than 1/2 psig (3.5 kpa).

DO NOT use this heater in recreational vehicles, bedrooms or

bathrooms.

If this is the ONLY gas appliance, we recommend a

minimum 200 pound cylinder with a fill gauge.  Use of a 100
pound cylinder is not recommended.  Other household gas
appliances may require the tank size to be larger.  Do not
operate the vent-free heater if the fuel level in the propane
tank is below 1/4 full.

WARNING:  During manufacturing, fabricating and
shipping, various components of this appliance are
treated with certain oils, films or bonding agents.  These
chemicals are not harmful but may produce annoying
smoke and smells as they are burned off during the
initial operation of the appliance, possibly causing
headaches and eye/lung irritation.  This is a normal and
temporary occurrence.

WARNING:  Do not use a blower insert, heat exchanger
insert or other accessory not approved for use with this
heater.

WARNING:  If the area in which the heater may be oper-
ated is smaller than that defined as an unconfined space
or if the building is of unusually tight construction,
provide adequate combustion and ventilation air by one
of the methods described in the National Fuel Gas code,
ANSI Z223.1, section 5.3 or applicable local codes.

This heater shall not be installed in a confined space or
unusually tight construction unless provisions are
provided for adequate combustion and ventilation air.

WARNING: Any change to this heater or its controls can
be dangerous.

This appliance is only for use with the type of gas indi-
cated on the rating plate. This appliance is not convertible
for use with other gases.

This appliance may be  installed  in an aftermarket,
permanently located, manufactured (mobile) home,
where not prohibited by local codes.

Содержание VF36RN

























Отзывы: