manualshive.com logo in svg

Temco DV1000N, Инструкция по установке и эксплуатации

Поделиться
Скачать
Temco DV1000N Скачать руководство пользователя страница 3

3

Temco DV1000/1200/1400 Series

76657

Installation & Operating Instructions

This gas appliance should be installed by a qualified 
installer in accordance with local building codes and with 
current 

CSA-B149.1

 Installation codes for Gas Burning 

Appliances and Equipment. For U.S.A Installations follow 
local codes and/or the current 

National Fuel Gas Code. 

ANSI Z223.1/NFPA 54

.

FOR SAFE INSTALLATION AND OPERATION PLEASE 
NOTE THE FOLLOWING:

1 .  This fireplace gives off high temperatures and should be 

located out of high traffic areas and away from furniture and 
draperies.

2.   Children and adults should be alerted to the hazards of the 

high surface temperatures of this fireplace and should stay 
away to avoid burns or ignition of clothing.

3.  

CAUTION: Due to high glass surface temperature chil-
dren should be carefully supervised when in the same 
room as fireplace.

The embers supplied with your fireplace are 
made from a high grade rock wool and should be 
handled carefully.  Wash your hands immediately 
after touching to avoid irritation.  The embers 
must be placed correctly in order to function 
properly.

This appliance may be installed in an aftermarket 
permanently located, manufactured home or mo-
bile home, where not prohibited by local codes.
This appliance is only for use with the type of gas 
indi-cated on the rating plate. This appliance is 
not convertible for use with other gases, unless a 
certified kit is used.

IMPORTANT:

PLEASE READ THE FOLLOWING CAREFULLY

Remove any plastic from trim parts before turning the 
fireplace ON.
It is normal for fireplaces fabricated of steel to give off 
some expansion and/or contraction noises during the 
start up or cool down cycle. Similar noises are found 
with your furnace heat exchanger or car engine.  It 
is not unusual for your gas fireplace to give off some 
odor the first time it is burned. This is due to the 
manufacturing process.

Please ensure that your room is well ventilated

-open all windows.

It is recommended that you burn your fireplace for at 
least four (4) hours the first time you use it. If the op-
tional fan kit has been installed, place the fan switch 
in the “OFF” position during this time.

WARNING: When purging the gas line, the glass 
front must be removed.

�������

�

���������

�����

������������

������������

������

�������������

�����

���������������

���������������

4.   Under no circumstances should this fireplace be modified. 

Parts removed for servicing should be replaced prior to 
operating this fireplace again.

5.  Installation and any repairs to this fireplace must be per-

formed by a qualified installer, service agency or gas sup-
plier. A professional service person should be contacted to 
inspect this fireplace annually. Make it a practice to have 
all of your gas fireplaces checked annually. More frequent 
cleaning may be required due to excess lint and dust from 
carpeting, bedding material, etc.

6.  Control compartments, burners and air passages in this fire-

place should be kept clean and free of dust and lint. Make 
sure the gas valve and pilot light are turned off before you 
attempt to clean this fireplace.

7.  The venting system (chimney) of this fireplace should be 

checked at least once a year and if needed your venting 
system should be cleaned.

8.  Keep the area around your fireplace clear of combustible 

materials, gasoline and other flammable vapor and liquids. 
This fireplace should not be used as a drying rack for cloth-
ing, nor should Christmas stocking or decorations be hung 
in the area of it.

9.  Under no circumstances should any solid fuels (wood, coal, 

paper or cardboard etc.) be used in this fireplace.

10. For safe operation, the glass door must be closed.
11. Do not use this heater if any part has been under water. 

Immediately call a qualified service technician to inspect the 
heater and to replace any part of the control system and any 
gas control which has been under water.

12. Do not operate appliance unless completely installed as per 

installation instructions.

13. This appliance may be used in a bedroom installation. Install 

in accordance with local building codes and regulations. 

14. Never use your fireplace as a cooking device.

DV1000 / DV1200 / DV1400

Certified To

ANSI Z21.88-2005 / CSA 2.33-2005 / UL 307B 

Vented Gas Fireplace Heater

WARNING: Check with your electronics manufac-
turer before installing a television or other elec-
tronic device above this fireplace.

Содержание DV1000N









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды