Teltone M-392 Скачать руководство пользователя страница 46

Страница: 46 / 52

Appendix 1: Specifications

M-392-A/B, M-393-A/B, and M-394-A/B Line Sharing Switches

Power Requirements

20 VDC

≤

DC Input

≤

34 VDC.

Maximum current draw = 500 mA
UL/CSA-recognized supply included with unit.

24 VDC, 120 VAC

10 %, 60 Hz, 0.2 A max.

No internal fusing required.

Environmental Requirements

Versions 250-00187-18 or higher

Operating Temperature
Storage Temperature

Versions 250-00187-17 or lower

Operating Temperature
Storage Temperature

Humidity

-20°C to +60°C
-40

C to +70°C (upper limit up to 3 days)

0°C to +50°C

-40

C to +60°C (upper limit up to 3 days)

90% maximum non-condensing, relative

Incoming Line Ring Detect

Frequency
Voltage
Ringer Equivalence

Ring trips within 200 mS after end of first ring cycle.
5 to 68 Hz
50 VRMS min
2.0B Max

Incoming Loop Hold Circuit

DC resistance of approximately 240 ohms.

Local Ring Generator

50 VRMS minimum at 5 ringer equivalence

Ringing frequency

Rounded square wave output at 20 Hz
2.0 S on/4.0 S off

10%

DTMF Receiver Parameters

Jack A

Receive level
Receive timing

Port 1 - 4

Receive level

-10 to -40 dBm
40 mS min

+10 to -20 dBm

Loop Current On-Hook/Off-Hook Detection

Unit detects off-hook when loop current is

≥

20 mA .

Unit detects on-hook when loop current is

≤

Forced Disconnect Recognition

350 mS

50 mS

Port 1 - 4 Rotary Signaling Detection

% Break
Interdigit Time

8 - 22 pps
40% to 80%
300 mS min

Jack A - Rotary Dialing Parameters

Rate
Interdigit time

10 pps 60% break
740 mS

5 mS

Local Battery Feed

On-hook voltage

40-52 volts DC.

Off-hook local battery

(short circuit loop current)

30 mA maximum

Call Progress Tone Characteristics

Jack A transmit level
Port 1 - 4 transmit level
Ringback Tone
Busy Tone
Dial Tone
Stuttered Dial Tone
Fast Busy Tone
CNG Tone detection (Fax Port)

receive level

Confirmation Tone

-10

3 dBm (combined) into 900

Ω

-18

3 dBm (combined) into 900

Ω

440 + 480 Hz 2.0 S on/4.0 S off
480 + 620 Hz, 500 mS on/500 mS off
350 + 440 Hz continuous
1 S delay, 3 bursts 100 mS on/off then continuous
970 Hz

10%, 250 mS on/250 mS off

1100 Hz

100 Hz

-10 to -45 dBm
2125

25 Hz, -13 dBm into 900

Ω

Watchdog Timer/Low Supply Voltage Detector

Provided in unit. If the microcontroller does not toggle the watchdog timer for
150 ms, the microcontroller is reset. When on-card 5 volt supply is

≤

4.5 volts,

the controller is held reset. Normal phone service is not affected by reset and
exit from reset conditions.

Indicator Lights

Green power and status indicator.

Dimensions/Weight

1.50" H x 5.50"W x 9.00"D, 1 lb. 8 oz.

Line Sharing Switch

Page 38

Содержание M-392





















































Результаты поиска

Содержание M-392

Отзывы:

Teltone M-392, Руководство по эксплуатации продукта, Страница: 46 / 52

Результаты поиска

Содержание M-392

Отзывы: