Teltone M-392 Скачать руководство пользователя страница 41

Страница: 41 / 52

Table 5 Routing Codes

Routing Code

Transfer Code

LSS Port

∗

Unit 1

Port 2

∗

Unit 1

Port 3

∗

Unit 1

Port 4

∗

Unit 2

Port 2

∗

Unit 2

Port 3

∗

Unit 2

Port 4

∗

Unit 3

Port 2

∗

Unit 3

Port 3

∗

Unit 3

Port 4

∗

Unit 4

Port 2

∗

Unit 4

Port 3

∗

Unit 4

Port 4

∗

Unit 5

Port 1

∗

Unit 5

Port 2

∗

Unit 5

Port 3

∗

Unit 5

Port 4

When assigning transfer codes for remote programming or for ports,

all codes must be

unique and must have the same number of digits.

Select a port on one of the daisy-chained LSS units.

Choose the routing codes (

01 -

16) that you want associated with that port.

Assign a unique transfer code to that port.

Fill in the table on the next page by assigning the transfer codes to units and ports.

Daisy-chain Remote Programming

If you are going to use remote programming in a daisy-chain, follow the steps below to
configure the LSS units.

Using

07#n#x#, the Transfer Code for Remote Programming command, assign a

different remote programming transfer code to each LSS in the daisy-chain.

For your reference, enter the unit number of the LSS in the last column of Table 6.
When assigning transfer codes for remote programming,

all codes must be unique

and must have the same number of digits.

Table 6 Remote Programming Daisy-chained LSS Units

Transfer Code for

Remote Programming

Remote Programming Code

LSS to be Programmed

PROPRIETARY

Reference Manual

Chapter 6: Advanced Applications

40-400-00015, Rev.

Page 33

Содержание M-392





















































Результаты поиска

Содержание M-392

Отзывы:

Teltone M-392, Руководство по эксплуатации продукта, Страница: 41 / 52

Результаты поиска

Содержание M-392

Отзывы: