Telit Wireless Solutions HE910 Скачать руководство пользователя страница 7

Страница: 7 / 111

HE910 Hardware User Guide

1VV0300925 Rev. 32

Page

111

2019-11-25

11.

USB HSIC .................................................................................. 75

12.

SERIAL PORTS ......................................................................... 77

MODEM SERIAL PORT 1 (USIF0) ............................................. 78

MODEM SERIAL PORT 2 (USIF1) ............................................. 81

RS232 level translation ............................................................... 82

13.

AUDIO SECTION OVERVIEW ................................................... 84

Electrical Characteristics ............................................................. 84

13.1.1.

CODEC Examples ...................................................................... 84

14.

GENERAL PURPOSE I/O .......................................................... 85

GPIO Logic levels ....................................................................... 86

Using a GPIO Pad as INPUT ...................................................... 87

Using a GPIO Pad as OUTPUT .................................................. 87

Indication of network service availability ..................................... 88

RTC Bypass out .......................................................................... 89

External SIM Holder Implementation ........................................... 89

VAUX Power Output ................................................................... 89

ADC Converter ........................................................................... 90

14.8.1.

Description .................................................................................. 90

14.8.2.

Using ADC Converter ................................................................. 90

15.

MOUNTING THE HE910 ON THE APPLICATION ..................... 91

General ....................................................................................... 91

Module finishing & dimensions .................................................... 91

Recommended foot print for the application ................................ 93

Stencil ......................................................................................... 94

PCB pad design .......................................................................... 94

PCB pad dimensions .................................................................. 95

Solder paste ............................................................................... 97

15.7.1.

HE910 Solder reflow ................................................................... 97

Packing system (Tray) ................................................................ 99

Packing System (Reel) ............................................................. 102

15.9.1.

Carrier Tape Detail ................................................................... 102

15.9.2.

Reel Detail ................................................................................ 103

15.9.3.

Packaging Detail ....................................................................... 104

Moisture sensitivity ................................................................... 104

16.

SAFETY RECOMMANDATIONS ............................................. 105

FCC/IC Regulatory notices ....................................................... 106

Содержание HE910
















































































































Результаты поиска

Содержание HE910

Отзывы:

Похожие инструкции для HE910

Бренды по названию

Популярные бренды

Telit Wireless Solutions HE910, Руководство пользователя по оборудованию

Результаты поиска

Содержание HE910

Отзывы:

Похожие инструкции для HE910

Бренды по названию

Популярные бренды