Telit Wireless Solutions GS2101M Series Скачать руководство пользователя страница 35

Страница: 35 / 196

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0

2019-08-05

3.2.1.2 Software Flow Control

This command is used to enable or disable software flow control for the UART interface.

Command Syntax

AT&Kn

Parameter Description

Table 12, page 35

describes the Software Flow Control parameters.

Synchronous Response

Table 13, page 35

describes the synchronous responses and remarks for the Software Flow

Control command.

Table 12 Software Flow Control Parameters

Parameter

Optional/Mandatory

Value

Description

Mandatory

0 (default)

Software flow control is disabled.

Software flow control is enabled.

Table 13 Software Flow Control Synchronous Responses

Responses

Remarks

Success

ERROR:INVALID INPUT

If parameter is not valid.
(other than 0 or 1)

Содержание GS2101M Series





































































































































































































Результаты поиска

Содержание GS2101M Series

Отзывы:

Похожие инструкции для GS2101M Series

Бренды по названию

Популярные бренды

Telit Wireless Solutions GS2101M Series, Справочник по командам

Результаты поиска

Содержание GS2101M Series

Отзывы:

Похожие инструкции для GS2101M Series

Бренды по названию

Популярные бренды