Telit Wireless Solutions GS2101M Series Скачать руководство пользователя страница 138

Страница: 138 / 196

GS2101M IP2WiFi Adapter Command Reference Guide

1VV0301499

Rev. 2.0

138

2019-08-05

Chapter 6 Power Management - Radio and System

This chapter describes the commands for configurations and operations related to power
management for radio and system.

•

Radio Receiver Setting, page 138

•

Battery Measurement, page 144

•

System Power Save, page 148

6.1 Radio Receiver Setting

6.1.1 Active Radio Receive

This command is used to enable/disable the 802.11 radio receiver. This minimizes latency
and ensures that packets are received at the cost of increased power consumption. The GS
node cannot enter Deep Sleep (see

6.3.3 Deep Sleep, page 155

) even if it is enabled

(AT+PSDSLEEP). The Power Save mode (see

6.1.3 Custom Power Save Radio Receive,

page 143

) can be enabled but will not save power, since the receiver is left on.

Command Syntax

AT+WRXACTIVE=n

Parameter Description

Table 117, page 138

describes the Enable/Disable 802.11 Radio parameters.

Synchronous Response

Table 118, page 138

describes the synchronous responses and remarks for the

Enable/Disable 802.11 Radio command.

Table 117 Enable/Disable 802.11 Radio Parameters

Parameter

Optional/Mandatory

Value

Description

Mandatory

0 (default)

802.11 radio receiver is off

802.11 radio receiver is always on

Table 118 Enable/Disable 802.11 Radio Synchronous Responses

Responses

Remarks

Success

ERROR: INVALID INPUT

Invalid parameter
(If

value is other than 0 or 1)

Содержание GS2101M Series





































































































































































































Результаты поиска

Содержание GS2101M Series

Отзывы:

Похожие инструкции для GS2101M Series

Бренды по названию

Популярные бренды

Telit Wireless Solutions GS2101M Series, Справочник по командам

Результаты поиска

Содержание GS2101M Series

Отзывы:

Похожие инструкции для GS2101M Series

Бренды по названию

Популярные бренды