background image

TELIKOU

  MS-500(4+1Channel)Main Station 

  1 

Contents 

I. 

General 

II. 

Specialty 

III. 

Basic operation   

1.  Front panel 

1)  Microphone switch (Mic.) 

2)  Announce switch (ANN.) 

3)  Call switch (Call) 

4)  Tone Alert volume control (Tone Alert) 

5)  Microphone Selection switch (Mic. Select) 

6)  Panel Microphone plug (Panel) 

7)  Headset plug (Headset

 

8)  Panel Microphone Gain control (Panel Mic. Gain) 

9)  Remote Microphone switch (RMK) 

10)  Listen Volume control (Volume) 

11)  Announce LED (ANN. LED) 

12)  Microphone LED (Mic. LED) 

13)  Talk LED (Talk LED) 

14)  Call LED (Call LED) 

15)  Program Level control (Program Level) 

16)  Program Feed To LED (Feed To LED) 

17)  Program Feed To switch (Program Feed To) 

18)  Power LED (Power LED) 

19)  Power Switch (Power) 

20)  Speaker (Speaker) 

21)  Sidetone Null control (Sidetone Null) 

A).Sidetone Null control on gooseneck microphone and panel speaker 

B).Sidetone Null control on headset 

C).Sidetone Null control on system 

22)  Talk With switch (Talk With) 

23)  Party-Line talk switch (PL) 

2.  Rear Panel 

24)  Announce output connector (ANN. Out) 

25)  Program Input connector (Prog. In) 

26)  Online connector (Online

 

27)  Termination switch (Termination) 

Содержание MS-500
















Отзывы: