Telguard Dual Path Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 42

background image

TG-7 Dual Path Series Installation & Operating Guide

27

56052601 Rev B © 2022 Telguard

Tamper Switch Installation for TG-7E UL/ULC Commercial Burglary Applications

For all UL/ULC Commercial Burglary Installations, a Tamper switch must be wired to monitor the
TG-7E enclosure. The wiring from Tamper Switch to the panel shall be in a rigid or flexible metal
conduit or be supervised along with other wiring from the TG-7E to the Panel. The tamper switch
does not connect to the TG-7E circuit board.

An easy-attach tamper switch assembly is included with the TG-7E communicator and contains
installation instructions. If a tamper switch is needed for a TG-7FE product, the TG-TAMPER
Accessory can be purchased from most Telguard distributors. Note that a tamper switch is required
when using the TG-7FE in a combination fire and burglary system.

LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8

ALARM PANEL

TRIP

INPUT

EARTH
GROUND

NOTE 2

NOTE 2: UL/ULC BURG NOTE: Tamper
switch should be mounted on the TG-7E
enclosure and connected to Alarm Panel.

R

ROUTER, SWITCH,
or OTHER LAN PORT

AC

Plug-in

Adapter

Battery

NOTE 1

NOTE 1: Use either AC Power
(from Adapter) with Battery
or use DC Power (from Panel).

NOTE 1

TAMPER

SWITCH

A

n

te

n

n

a

«
...
31
32
33
34
35
...
»

Содержание Dual Path Series











































Отзывы:

Нет отзывов

Похожие инструкции для Dual Path Series

Memoir SGH t929

Бренд: Samsung Страницы: 200

Бренд: Topcom Страницы: 76

Бренд: lepow Страницы: 2

Бренд: UNITe IP Страницы: 116

Бренд: BLU Products Страницы: 22

Zentral AV Remote Control

Бренд: Acoustic Research Страницы: 20

Бренд: Samsung Страницы: 117

Бренд: Samsung Страницы: 147

Бренд: Samsung Страницы: 107

Бренд: Samsung Страницы: 40

Бренд: Samsung Страницы: 26

JetSet SCH-R550 Series

Бренд: Samsung Страницы: 152

Бренд: Samsung Страницы: 124

Бренд: Samsung Страницы: 174

Бренд: Emerson Страницы: 214

Бренд: Hitachi Страницы: 61

Бренд: Lenovo Страницы: 33

Бренд: Lenovo Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды