background image

1.

On/Off Switch

 – Turns the power on/off to the base

station.

2.

Power / Low Battery Light

 – Indicates the base

station has power, either from the internal battery or
external power connected to the unit.

Battery Indication:

GREEN - Battery OK

RED - Battery Low (needs charged)

3.

Transmit Antenna Jack

 – This reverse TNC jack is

where the transmit antenna coaxial cable should be
connected.

4.

AP Active Light

 – This green light flashing indicates

that the AP has successfully booted and is operating.

5.

Gooseneck Antenna Mount Lug

 - Provides

attachment point for the gooseneck antenna mount.

6.

RF Channel Display

 – Indicates the RF channel the

unit is set on.

7

.

Receive Antenna Jack

 – This reverse TNC jack is

where the receive antenna coaxial cable should be
connected.

8.

Select Button  –

 Press the button to select the desired

RF channel for the base station.

ClearScan

 – Press and hold the button until the

decimal point starts to flash (about 3 seconds)
then release. The unit will examine the RF
channels available, then select the one with the
least activity and set the AP on that channel.

Lock

 – Press and hold the button until the

decimal point is on solid (about 10 seconds)
then release. The AP will be locked on the
channel displayed. To unlock, press and hold
the button again until the decimal point is off.
Lock makes the currently displayed channel
difficult for a user to accidentally change.

9.

Charge Jack 

– Used to charge the internal battery or

power the unit directly off a wall outlet. Accepts a
5.5mm x 2.5mm plug with the center positive. Must be
supplied with a 12VDC regulated power supply with at
least a 400mA current capacity.

10.

Charge Light.

RED = Battery is charging.

GREEN = Battery is charged.

11.

Programming Jack

 – This RJ-45 jack is used for

programming the unit at the factory.

ON

OFF

RECEIVE
ANTENNA

POWER

LOW

BATTERY

AP

ACTIVE

CHANNEL

TRANSMIT
ANTENNA

SELECT

CHANNEL
CLEAR SCAN
LOCK

XO-AP

Telex

1

3

2 4

5 6

7

8

Section 2 - XO-AP Base Station

Controls and Connections                    

2-1

CORD

RETAINER

12 VDC

400mA

RED: CHARGING
GREEN: READY

PGM

9

10

11

Front View

Rear View

Содержание Legacy XO-1




















Отзывы: