background image

 

 

                                                                                                                                                                                                                      3 

II. Notice: 
 
Signal  Communications  Limited  reserves  the  right  to  make  improvements  to  the  product 
described in this manual at any time and without prior notice. 
 
This manual is copyrighted. All rights are reserved. This manual may not be copied, reproduced 
or translated in whole or part without prior consent from Signal Communications Limited. 
 
Tele  Eye  is  a  trademark  of  Signal  Communications  Limited  and  is  registered  in  China,  Hong 
Kong, US and other countries. 
 
TeleEye's products are sold under the brand name of CAMERIO in Australia, Japan, Korea, New 
Zealand, Taiwan and Argentina. 
 
CAMERIO is a trademark of Signal Communications Limited and is registered in Australia, Japan, 
Korea, New Zealand, Taiwan and Argentina.   
 
All other trademarks are the property of their respective owners 
Copyright  (c)  2007  Signal  Communications  Limited  (A  Member  of  TeleEye  Group).  All  rights 
reserved. 
 
Version 1.1 
 
Limits of Liability and Disclaimer of Warranty 
Signal  Communications  Limited  has  taken  care  in  preparation  of  this  manual,  but  makes  no 
expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. 
 
No liability is assumed for incidental or consequential damages in connection with or arising out 
of the use of the information or accessories contained herein. 
 
Features and specifications are subject to change without prior notice. 

 

 

 

 

 

 

 

 

 

 

 

Содержание DM587



























Отзывы: