Teledyne Kuro Скачать руководство пользователя страница 44

44

Kuro sCMOS Camera System Manual

Issue 2

Sealed Chamber Integrity Limited 12 Month Warranty

Teledyne Princeton Instruments warrants the sealed chamber integrity of all our products 
for a period of twelve (12) months after shipment. If, at anytime within twelve (12) months 
from the date of delivery, the detector should experience a sealed chamber failure, all 
parts and labor needed to restore the chamber seal will be covered by us. 

Open chamber 

products carry NO WARRANTY TO THE CCD IMAGING DEVICE, EXPRESSED OR IMPLIED.

 

Responsibility for shipping charges is as described above under our Basic Limited One (1) 
Year Warranty.

Vacuum Integrity Limited 12 Month Warranty

Teledyne Princeton Instruments warrants the vacuum integrity of “Non-XP” style 
detectors (do not have all metal seals) for a period of up to twelve (12) months from the 
date of shipment. We warrant that the detector head will maintain the factory-set 
operating temperature without the requirement for customer pumping. Should the 
detector experience a Vacuum Integrity failure at anytime within twelve (12) months from 
the date of delivery all parts and labor needed to restore the vacuum integrity will be 
covered by us. Responsibility for shipping charges is as described above under our Basic 
Limited One (1) Year Warranty.

Image Intensifier Detector Limited One Year Warranty

All image intensifier products are inherently susceptible to Phosphor and/or 
Photocathode burn (physical damage) when exposed to high intensity light. Teledyne 
Princeton Instruments warrants, with the exception of image intensifier products that are 
found to have Phosphor and/or Photocathode burn damage (which carry NO 
WARRANTIES EXPRESSED OR IMPLIED,) all image intensifier products for a period of one 
(1) year after shipment. 

Refer to additional Limited One (1) year Warranty terms and 

conditions above, which apply to this warranty.

 Responsibility for shipping charges is as 

described above under our Basic Limited One (1) Year Warranty.

X-Ray Detector Limited One Year Warranty

Teledyne Princeton Instruments warrants, with the exception of CCD imaging device and 
fiber optic assembly damage due to X-rays (which carry NO WARRANTIES EXPRESSED OR 
IMPLIED,) all X-ray products for one (1) year after shipment. 

Refer to additional Basic 

Limited One (1) year Warranty terms and conditions above, which apply to this warranty.

 

Responsibility for shipping charges is as described above under our Basic Limited One (1) 
Year Warranty.

Software Limited Warranty

Teledyne Princeton Instruments warrants all of our manufactured software discs to be 
free from substantial defects in materials and/or workmanship under normal use for a 
period of one (1) year from shipment. Teledyne Princeton Instruments does not warrant 
that the function of the software will meet your requirements or that operation will be 
uninterrupted or error free. You assume responsibility for selecting the software to 
achieve your intended results and for the use and results obtained from the software. In 
addition, during the one (1) year limited warranty. The original purchaser is entitled to 
receive free version upgrades. Version upgrades supplied free of charge will be in the form 
of a download from the Internet. Those customers who do not have access to the Internet 
may obtain the version upgrades on a CDROM from our factory for an incidental shipping 
and handling charge. 

Refer to Item 12 in 

Your Responsibility

 of this warranty for more 

information.

Содержание Kuro

















































Отзывы: