Teledyne Lecroy AP031 Скачать руководство пользователя страница 12

Operator’s Manual 

923064-00 Rev A 

11 

Certifications 

This section certifies the AP031 probe’s Electromagnetic Compatibility (EMC), Safety and 
Environmental compliances. 

EMC Compliance 

EC Declaration of Conformity - EMC 

The probe meets intent of EC Directive 2004/108/EC for Electromagnetic Compatibility. 
Compliance was demonstrated to the following specifications as listed in the Official Journal 
of the European Communities: 
EN 61326-1:2006, EN 61326-2-1:2006 EMC requirements for electrical equipment for 
measurement, control, and laboratory use. 

 

Electromagnetic Emissions: 

CISPR 11:2003, Radiated and Conducted Emissions Group 1, Class A 

1 2 

 

Electromagnetic Immunity: 

EN 61000-4-2:2001 Electrostatic Discharge, 4 kV contact, 8 kV air, 4 kV vertical/horizontal 
coupling planes 

3

 

EN 61000-4-3:2006 RF Radiated Electromagnetic Field, 3 V/m, 80-1000 MHz; 3 V/m, 1400 
MHz - 2 GHz; 1 V/m, 2 GHz - 2.7 GHz 

3

 

1 Emissions which exceed the levels required by this standard may occur when the probe is connected to a test 
object. 
2 This product is intended for use in nonresidential areas only. Use in residential areas may cause electromagnetic 
interference. 
3 Meets Performance Criteria “B” limits of the respective standard: during the disturbance, product undergoes a 
temporary degradation or loss of function or performance which is self-recoverable. 

www.

.com

[email protected]

1.800.561.8187

Содержание AP031
















Отзывы: