Telect Dual-Feed 350A 10/10-TPA Скачать руководство пользователя страница 6

Страница: 6 / 15

1.509.926.6000 :: telect.com

Dual-Feed 350A 8/8-TPA & 10/10

GMT Fuse Alarm Panel

Power

:: 009-8005-0810

1.2.3 Installation Procedure

ALERT

ALERT! Only qualified personnel may install and

maintain this product. Verify that all connections

meet requirements specified in local electric

codes or operating company guidelines before

supplying power. Protect this equipment with a

fuse or breaker sufficient to interrupt power levels

specified in Section “1.2 Specifications” on page 1.

Install this product in locations accessible only by

qualified personnel.

Panel brackets provide flush or 5-in. extended EIA

or WECO mounting in a 23-in. or 19-in. rack with an

equipment aperture of at least 17.4 in. (442 mm)

between the rack’s flanges.

If necessary, remove the three screws and reposition

the brackets on the sides of the distribution panel, as

shown in Figure 2.

2. Locate an unused rack position and mount panel

using the four sets of screws and washers provided,

as shown in Figure 3. (It’s best to mount the panel

as high as possible on the rack.)

Tighten the screws to 35 in.-lb (4.29 N•m).

Loosen (you need not remove) the two screws

securing the rear terminal cover on the back of

the panel.

5. Remove the cover

WARNING

WARNING! Failure to properly ground this

equipment can create hazardous conditions

for installation personnel and for the equipment.

Holes for

Holes for 5-in.

Flush M ounting

Extended M ounting

Figure 2 - Bracket Orientation

Figure 3 - Rack Mounting

Содержание Dual-Feed 350A 10/10-TPA















Результаты поиска

Содержание Dual-Feed 350A 10/10-TPA

Отзывы:

Бренды по названию

Популярные бренды

Telect Dual-Feed 350A 10/10-TPA, Руководство пользователя

Результаты поиска

Содержание Dual-Feed 350A 10/10-TPA

Отзывы:

Бренды по названию

Популярные бренды