Telect Dual-Feed 350A 10/10-TPA Скачать руководство пользователя страница 3

Страница: 3 / 15

1.509.926.6000 :: telect.com

Dual-Feed 350A 8/8-TPA & 10/10

GMT Fuse Alarm Panel

Power

:: 009-8005-0810

1.1 Overview

Telect’s dual-feed 350A fuse panel with alarms provides

power protection for data and communications equipment

ranging from ¼A to 50A. The white panel includes 16

TPA output fuse holders (8 per side) and 20 GMT

holders (10 per side).

Sides A and B are electrically independent except

for the replaceable alarm card, which contains power

status LEDs for each side and power-fail and fuse-alarm

relays. Relay contacts are Form C for external visual

and audio indicators.

Hardware is included for flush or 5-in. extended mounting

in a 23-in. or 19-in., EIA or WECO rack. (The 19-in.

rack must have an equipment mounting aperture of at

least 17.5 in.) Visit our website for ordering Telect

accessories: fuses (3A-50A TPA & ¼ A-15A GMT),

ETSI bracket kit, spare alarm card, and more.

Model 009-8005-0810 is UL Listed (E139903), NEBS

compliant, and RoHS compliant.

Figure 1 - Model 009-8005-0810

Inputs:

Specifications:

Nominal Voltage

±24Vdc

-48Vdc

Max Input Load Rating

350A per side

Nominal Power Loss at Full Load

90W per side @ 16,800W full load per side

(350Ax48V)

Percentage of Full Power Dissipation atNominal Voltage

less than 1%

Max. Input Interrupt Device

450A

Input Terminal Studs (With Nuts, Flat Washers, &

Spring Washers) for Dual-Hole Compression Lugs

Two pairs of 3/8 - 16 studs on 1 in. centers (max. lug

width of 1.625 in. [41.27 mm]). Torque nut (using 9/16

in. or 15 mm wrench) to 140 in.-lb (~15½ N•m).

Input Wire Size

#1 AWG to 600MCM

Short Circuit Withstand

5000A

Содержание Dual-Feed 350A 10/10-TPA















Результаты поиска

Содержание Dual-Feed 350A 10/10-TPA

Отзывы:

Бренды по названию

Популярные бренды

Telect Dual-Feed 350A 10/10-TPA, Руководство пользователя

Результаты поиска

Содержание Dual-Feed 350A 10/10-TPA

Отзывы:

Бренды по названию

Популярные бренды