background image

Version 01   /   

p.37

AFA1000/BLD Pressure Controller 

 

Installation & Operating Manual

To Setup the AFA1000 with BACnet protocol using the pushbutton menus:-

1.

 

  Press Enter from the “Requires set up” screen or if the controller is in the Run 
screen Press and Hold the Enter button for 5 seconds until the Main Menu is 
displayed.

2.

 

 Using the + / - buttons select SET UP, and then select CONFIGURE, then enter 
the password (the factory default password is 0-0-0-0), press Enter to continue.

3.

 

 Using the + / - buttons select PROTOCOL, and press Enter, then using the +/- 
buttons select BACnet and then press Enter to return to the CONFIG MENU.

4.

 

 Using the + / - buttons select BACnet SETTINGS and then press Enter, a sub 
menu will appear with the following parameters:-

5.

 

 Using the + / - buttons select the DEVICE INSTANCE parameter and then press 
Enter, then using the +/- buttons select the required Instance and press Enter to 
continue.

6.

 

 Using the + / - buttons select the STATION ID parameter and then press Enter, 
then using the +/- buttons select the required ID and press Enter to continue.

7.

 

 Using the + / - buttons select the BAUD RATE parameter and then press Enter, 
then using the +/- buttons select the required rate and press Enter to continue.

8.

 

 Using the + / - buttons select the PARITY parameter and then press Enter, then 
using the +/- buttons select the required rate and press Enter to continue.

9.

 

 Using the + / - buttons select the MAX MASTERS parameter and then press 
Enter, then using the +/- buttons select the required number of Masters and 
press Enter to continue, then select DONE to return to the CONFIG MENU, then 
select DONE and RUN.

Parameter

Description

Range

Default

Device Instance Set the slave ID 

for the unit  

0000000 to 4194303

0000000

Station ID 

Set the network 

ID

0-127 

1

Baud Rate 

Set the required 

Baud Rate

1200/2400/4800/9600/1440/

19200/38400/57600

38400

Parity

Set the required 

Parity

None/Even/Odd

None

Max Masters

Set the max 

masters (max 

devices on the 

network)

0-127 

1

Содержание AFA1000/BLD












































Отзывы: