manualshive.com logo in svg

Tektronix TYPE L, Инструкция по эксплуатации

Поделиться
Скачать
Tektronix TYPE L Скачать руководство пользователя страница 29

C5072

C5222

C5292

C5362

V ert.  Pos.  Range 

R6572

V6042 Cathode  Current  Adj, 

R5922

Low   F req .  Adj.

C5272

C5342

C5602

C5432

C5412

C5502

R6182

Fig.  5-2.  Location of left-side  internal  adjustments  and  input  attenuator adjustments.

Set  the  TIME/CM  switch  at  50  M ILLISEC, 

the  AC-DC  switch  at  X10  GAIN  AC,  and  the 
VOLTS/CM  switch  at  .005.  Apply  a  50  cycle 
square  wave  from   the  Type  105  to  the  INPUT 
o f  the  Type  L   Unit  through  approximately  250 
to  1000X  attenuation.  Short  the  input  blocking 
capacitor  (C5001)  with  the  resistive  shorting 
strap.  Adjust  the  amplitude  of  the  display  to 
about  3  cm  with  the  OUTPUT  AM PLITUDE 
control  on  the  Type  105.  Set  the  Low  Freq. 
Adj.  control  on  the  left  side  of  the  L   Unit 
fo r  optimum  level  top  of  the  square  wave. 
Remove  the  clip  lead.

16.  H igh-Frequency  P eak in g

 

Adjustment

The  H.F.  Peaking  control  in  the  Output 

Stage  o f  the  Type  L   provides  for  matching 
the  impedance  of  the  cathode  circuit  to  the 
output  peaking  coils  fo r  best  high-frequency 
response.

Remove  the  Type  EP54  Plug-In  Extension. 

Set  the  TIME/CM  switch  at  .2  pSEC, VOLTS/ 
CM   at  .05  and the  AC-DC  switch  at  DC.  Install 
a  50ft  Terminating  Resistor  on  the  INPUT

connector  of  the  Type  L   Unit.  Apply  a  square 
wave  of  approximately  450  kc  from   a  Tektronix 
Type  107  Square-Wave  Generator  to  the  T e r ­
minating  Resistor  on  the  Type  L .  Adjust  the 
display 

amplitude  with  the  APPROXIM ATE 

AM PLITUD E  control  on  the Type 107 to approxi­

mately  3  cm.  Adjust  the  H.  F.  Peaking  control 
on  the  bottom  side  of the  Type  L   for  a  square- 
cornered  waveform  with  no  overshoot.

17.  X10  Am plifier  H igh-Frequency

 

Adjustments

Three  variable  peaking  coils  are  provided 

in  the  X10  am plifier fo r  adjusting  its  frequency 
response.

With  other  controls  set  as  in  step  16,  turn 

the  AC-DC  switch  to  X10  GAIN  AC.  With  the 

50ft  Terminating  Resistor  on  the  INPUT  con­

nector  of  the  Type  L ,  install  also  a  10X 
Attenuator  and  apply  a  450  kc  square  wave 
from   the  Type  107  as  before. 

Adjust  the 

display  amplitude  to  approximately  3  cm  with 

the  APPRO XIM ATE  AM PLITUDE  control  on 

the  Type  107.  Adjust  coils  L5902,  L5942  and 

L6012  fo r  a  square  leading  corner  of  the

AA

Calibration  Procedure  -  Type  L  Plug-In

5-5

Содержание TYPE L















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды