manualshive.com logo in svg

Tektronix RSA5103A, Инструкция по эксплуатации

Поделиться
Скачать
Tektronix RSA5103A Скачать руководство пользователя страница 15

Verify instrument software version

Attach the Export Control

classi

fi

cation label

Place the Export Control classi

fi

cation label on the instrument rear panel if you’ve

installed the Digital I and Q Outputs option.

NOTE.

The Export Control label applies only to the RSA5100B Series instruments

when installing Option 65 or Option 6566.

Verify instrument software version

Tektronix recommends to update to the latest available application software for
your instrument.

1.

Select

Help > About

to check the software version.

2.

Use your Web browser to go to: www.tektronix.com/software.

3.

Search for your instrument’s model number and follow the link to the software.

4.

If the installed software is older than that available, download the software.

5.

Follow the instructions on the Web page to install the software.

■

End of Document

■

RSA5100A/B Series Digital I/Q and Zero Span Upgrades

13

Содержание RSA5103A
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды