manualshive.com logo in svg

Tektronix DPO2304SX, Печатная инструкция


Поделиться
Скачать
background image

Error detector setups

Use the serial error detector

From the Analyze menu, select Serial Error Detector. Error detector is not available on DPO70000SX instruments.

Overview

The Serial Error Detector requires option ERRDT. The oscilloscope Error Detector conducts Bit, Frame, Symbol, and Character
tests much like a BERT. It has the advantage that it not only counts the errors and computes the error rates, but it also shows
you where the error occurs in the signal and it allows you to connect probes to other channels to debug the source of the errors,
such as crosstalk.

The Error Detector is often used in conjunction with TekExpress software applications to conduct receiver and margin testing.

The Error Detector has built-in preset setups that cover the most common use cases. These can be modified and saved as
custom setup files for later recall. Sample arbitrary waveform generator (AWG) setup files are included for various SATA Gen3
and USB3 signals. These files make it easy to verify correct operation of the Error Detector, and may be used to test a device-
under-test (DUT).

 

 

To use

■

Select Analyze > Serial Error Detector to display the Error Detector control window.

■

Select a setup from the Preset Setting drop-down list and press Apply.

■

Press the Sync button and wait for a status of Not Counting (about 6 seconds). Depending on the signal quality, you may
need to press the Sync button more than once.

Sync gets the oscilloscope synchronized to the signal.

A status of No Signal indicates that the oscilloscope cannot detect the signal. You may need to turn on the output of the
signal generator or AWG. A status of No Sync may arise for Bit tests that require a known pattern length, sync pattern, or
alignment character.

■

Press the Learn button, if visible. Learn only applies to some Bit Error Tests. Frame, Symbol, and Character tests do not
require the learn operation. Learn discovers the repeating pattern in the signal and stores it into system memory for
comparison to the signal to determine errors in the signal. Once a signal is in memory, it remains there until the next Learn
operation, so you do not have to use the Learn button every time you start testing for errors.

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series 

203

Содержание DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DPO2304SX

Taylor Made 12008 Instructions preview
12008
Бренд: Taylor Made Страницы: 2
York Fitness 1003 Assembly Instruction Manual preview
1003
Бренд: York Fitness Страницы: 18
Safco 1005 Instructions preview
1005
Бренд: Safco Страницы: 2
Omni 4000 Series Operation & Maintenance Manual preview
4000 Series
Бренд: Omni Страницы: 193
Keithley 261 Instruction Manual preview
261
Бренд: Keithley Страницы: 32
jcb CT160 Operator'S Manual preview
CT160
Бренд: jcb Страницы: 166
Rainbow Quantum Instruction Manual preview
Quantum
Бренд: Rainbow Страницы: 18
Parker Research Corp B100 Operating Instructions preview
B100
Бренд: Parker Research Corp Страницы: 4
Eastwood B100 Instructions Manual preview
B100
Бренд: Eastwood Страницы: 20
Daihan Scientific WiseSpin CF-10 Operation Manual preview
WiseSpin CF-10
Бренд: Daihan Scientific Страницы: 43
Eaton X10 Installation Manual preview
X10
Бренд: Eaton Страницы: 21
NANO Pulsar Operating Instructions preview
Pulsar
Бренд: NANO Страницы: 4
Garmin PORTABLE ICE FISHING KIT Installation Instructions preview
PORTABLE ICE FISHING KIT
Бренд: Garmin Страницы: 5
Waters 2707 Quick Install Manual preview
2707
Бренд: Waters Страницы: 4
Waterpik ClearView Instructions For Use preview
ClearView
Бренд: Waterpik Страницы: 2
Yamaha MagicStomp Effect List preview
MagicStomp
Бренд: Yamaha Страницы: 31
Zimmer OptonPro Operating Instructions Manual preview
OptonPro
Бренд: Zimmer Страницы: 54
Zimmer Cryo 6 Manual preview
Cryo 6
Бренд: Zimmer Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды