Tecnologic THP 84, Руководство по эксплуатации

Страница: 20 / 21

0 -999 ÷ 9999 Minimum alarm A4
threshold
AL4H
11
0 -999 ÷ 9999 Minimum alarm A4
threshold AL4L 10
0 -999 ÷ 9999 Alarm A4 threshold AL 4 9
0 -999 ÷ 9999 Minimum alarm A3
threshold AL3H 8
0 -999 ÷ 9999 Minimum alarm A3
threshold AL3L 7
0 -999 ÷ 9999 Alarm A3 threshold
AL 3
6
"COnF" MENU PARAMETERS TABLE
30 1 ÷ 255 sec. Output C1 cycle time tcr2 28
1.00 0.00 ÷ 99.99 C2 / C1 Power ratio Prat 27
30 1 ÷ 255 sec. Output C1 cycle time
tcr1
26
30 0 ÷ 9999 sec. Derivative time
dEr
25
500 0 ÷ 9999 sec. Integral time
Int
24
100 1 ÷ 9999 Proportional band Pb 23
SP SP / Load Autotuning optimisation PidP 22
no no / FaSt /
SP / LoSP Autotuning Auto 21
no no / yES Selftuning
SELF
20
AL4 AL4 /
Pid / 3Pt
Output C2/A4 functioning
mode C2 19
HEat HEat / CooL Output C1 operating
mode
Func
18
Pid Pid /
OnFS / OnFa
Control mode Cont 17
9999 SPLL ÷ 9999 High/maximum Set Point SPHL 16
-999 -999 ÷ 9999 Low/minimum Set Point SPLL 15
no no / yES Alarms programming on
"ConF" menu
ALPr
14
0 0 ÷ 9999 sec. Loop Break alarm
maximum time LbAt 13
0 0 ÷ 100 % Loop Break alarm power LbAP 12
OPEn OPEn / CLoS Output HB logic mode
rLHb
11
OFF OFF / On A4 Alarm behaviour in
OFF control mode
AL4o
10
- - C - - C / - - o
- SC / - So
L - C / L - o
LSC / LSo
Configuration of A4 alarm
functioning mode AL4c 9
LOAb LOAb / HIAb
LHAb / LOdE
HIdE / LHdE
A4 Alarm type AL4t 8
OFF OFF / On A3 Alarm behaviour in
OFF control mode AL3o 7
- - C - - C / - - o
- SC / - So
L - C / L - o
LSC / LSo
Configuration of A3 alarm
functioning mode AL3c 6
LOAb LOAb / HIAb
LHAb / LOdE
HIdE / LHdE
A2 Alarm type
AL3t
5
Hb AL3, Hb A3/HB output functioning
mode FAL3 4
1 -999 ÷ 9999 Alarm A4 hysteresis HAL4 3
1 -999 ÷ 9999 Alarm A3 hysteresis HAL3 2
1 0 ÷ 9999 Set point hysteresis for
ON/OFF control mode
HSEt
1
Notes Def. Range Description Par.
no no / yES Active Set-point change
using "UP" key
SPOL
55
no no / yES Manual contron activation
in "SEL" menu EnOL 54
0 -99.9 ÷100.0 % Manual control power
when activated by
AUXIN
rEdF
53
FF FF /Fr /rF /rr AUXIN input function
rEAr
52
1 1 ÷ 4 Programmable Set-point
number nSP 51
LoCL LoCL / LorE Programming access
through serial port
PacS
50
4800 300/600/1200/
2400/4800/
9600 baud
Baud rate serial port baud 49
1 1 ÷ 255 Address of the station for
serial comunication
nSta
48
50H 50H / 60H Hz Frequency optimizing the
noise FrEq 47
1 0 ÷ 50 sec. Input digital filter
constant
Filt
46
0 -999 ÷ 9999 Calibration
OFFt
45
0 0 / no_0 Analogue outputs range
Aout
44
0 -999 ÷ 9999 Higher limit of analogue
input scale for normalized
signals EndS 43
0 -999 ÷ 9999 Lower limit of analogue
input scale for normalized
signals StrS 42
0 0 ÷ 3 Number of decimal
figures
dP
41
SSLo SSLo / SSHi Range of analogue input
for normalized signals ScaL 40
C C / F / r Unit of measurement Unit 39
0.0 -99.9 ÷ 999.9
°C/°F/°R
Cold junction temperature
compensation
tCJC
38
no no / YES Cold junction external
compensation ECJC 37
J b / E / J / CrAl
/ n / r / S / t / L
/ u / Pt1 / Pt2 /
0_50
Input probe
SEnS
36
0.00 0.00 ÷ 99.99
unit/min.
Gradient of fall ramp SloF 35
0.00 0.00 ÷ 99.99
unit/min.
Gradient of rise ramp
Slor
34
no no /
OPEn / CloS
Positioning at start-up of
motorized actuactor PoSi 33
0 0 ÷ 9999 Dead zone dbEr 32
0 0 ÷ 10 % Minimum control value of
motorized actuator SHrI 31
4 4 ÷ 1000 sec. Travel time of the
motorized actuator tcor 30
50.0 -99.9÷100.0 % Manual reset
rS
29
7 - PROBLEMS, MAINTENANCE AND WARRANTY
ERRORS SIGNALLING:
The 2 displays are used as well to visualise
anomaly conditions of instrument functioning :
"- - - -" = probe interruption.
"uuuu" = the measured variable is gone under the probe limits.
"oooo" = the measured variable is gone under the probe limits.
"u400" = the temperature is gone under 400°C when it's used a
thermocouple "B" type. The regulation regularly proceeds considering PV
= 0°C.
"LbA" = interruption of the regulation ring (see loop break alarm
function).
TECNOLOGIC - THP 84 USER MANUAL (I - GB) - Vr. 02 - ISTR 00132 - PAG. 20