TECNOEKA KCV 96, Инструкция по использованию

Страница: 11 / 20

_ Electric Cookers _ rev. 1 _________________________________________________________ KCV 96 P – KCV 96_
_ CATEGORY II2H3+ _ GB __
0705
_____________________________________________________ page 11 _
The power cable must comply with the following characteristics:
KCV 96 P KCV 96 P KCV 96 P KCV 96 P KCV 96 KCV 96 KCV 96 KCV 96
Power supply voltage Power supply voltage Power supply voltage Power supply voltage (V~) (V~) (V~) (V~) 220 – 230 380 – 400 2N
Power cable diameter
Power cable diameter Power cable diameter
Power cable diameter 3x1.5 mm
2
4x2.5 mm
2
Type of power cable Type of power cable Type of power cable Type of power cable H07RN-F
Safety device Safety device Safety device Safety device - The appliance is supplied with a manually resetting thermal breaker to protect
against excessive, dangerous temperatures which could be accidentally generated inside the
oven. If tripped, the device cuts out electrical power to the appliance. To access this device,
remove the panel at the rear of the appliance.
6. 6. 6. 6. Adapting cook Adapting cook Adapting cook Adapting cook----top top top top to different types of gas to different types of gas to different types of gas to different types of gas
To adapt the hob to a type of gas that differs
from the one tested in the factory (see data plate
or supplementary plate), replace the nozzles of
the five burners Remove the pan carrier grilles
from the hob and withdraw the movable parts of
the burners from their seats:
-
Remove the pot support grids from the
cook-top and remove the mobile parts of
the burners from their position.
-
Unscrew the jets (Fig. 2) using the 7 mm.
Key and replace them with the new ones
(see
table 1). Check the exact
correspondence of the diameter indicated
on the table with that printed on the jets.
After having replaced the jets, set up all the
parts again and stick the new data on the
technical data plate.
Fig. Fig. Fig. Fig. 2 2 2 2
N.B. N.B. N.B. N.B. The burners don’t need any air regul The burners don’t need any air regul The burners don’t need any air regul The burners don’t need any air regulation ation ation ation....
Minimum level adjustment Minimum level adjustment Minimum level adjustment Minimum level adjustment - Burner minimum levels are preset for methane gas (G20)
operation. If operating on liquid gas (G30/G31) proceed as follows: ignite the burner at
minimum position, and, using a screwdriver, fully tighten the by-pass adjustment screw at the
side of the shank of the relevant tap. Check if the flame remains stable and uniform – to help
you check, rapidly turn the tap knob from maximum to minimum position. When you have
finished adjusting the by-pass valve, seal it with red paint. Make sure you fit a plate with the
new installation data. After having set the by-pass screw, seal it with red varnish.
Gas pressure (mbar)
Gas pressure (mbar) Gas pressure (mbar)
Gas pressure (mbar)
Type of gas Type of gas Type of gas Type of gas Normal Normal Normal Normal Max. Max. Max. Max. Min. Min. Min. Min.
Table 1
Table 1 Table 1
Table 1
G30
G30 G30
G30 30
30 30
30 35
35 35
35 20
20 20
20
G31 G31 G31 G31 37 37 37 37 45 45 45 45 25 25 25 25
G20 G20 G20 G20 20 20 20 20 25 25 25 25 17 17 17 17
Main nozzles diameter
Main nozzles diameter Main nozzles diameter
Main nozzles diameter
(1/100 mm) (1/100 mm) (1/100 mm) (1/100 mm)
By By By By----pass screw nozzles pass screw nozzles pass screw nozzles pass screw nozzles
diameter diameter diameter diameter
(1/100 mm)
(1/100 mm) (1/100 mm)
(1/100 mm)
Consumption calculated with gross
Consumption calculated with gross Consumption calculated with gross
Consumption calculated with gross
heat values heat values heat values heat values
Nominal Nominal Nominal Nominal
thermal
thermal thermal
thermal
capacity capacity capacity capacity
(kW) (kW) (kW) (kW)
Reduced Reduced Reduced Reduced
thermal
thermal thermal
thermal
capacity capacity capacity capacity
(kW) (kW) (kW) (kW)
G30/G31 G30/G31 G30/G31 G30/G31
30/37mbar 30/37mbar 30/37mbar 30/37mbar
G20 G20 G20 G20
20mbar 20mbar 20mbar 20mbar
G30/G31 G30/G31 G30/G31 G30/G31
30/37mbar 30/37mbar 30/37mbar 30/37mbar
G20 G20 G20 G20
20mbar 20mbar 20mbar 20mbar
G30 G30 G30 G30
30mbar
30mbar 30mbar
30mbar
(g/h)
(g/h) (g/h)
(g/h)
G31 G31 G31 G31
37mbar
37mbar 37mbar
37mbar
(g/h)
(g/h) (g/h)
(g/h)
G20 G20 G20 G20
20mbar
20mbar 20mbar
20mbar
(l/h)
(l/h) (l/h)
(l/h)
Triple crown Triple crown Triple crown Triple crown
burner Nr.
burner Nr. burner Nr.
burner Nr. 1
1 1
1
3. 3. 3. 3.5 5 5 5 1. 1. 1. 1.8 8 8 8 95 95 95 95 135 135 135 135 74 74 74 74 Regul. Regul. Regul. Regul. 255 255 255 255 250 250 250 250 334 334 334 334
Fast Fast Fast Fast burner burner burner burner
Nr.
Nr. Nr.
Nr. 3
3 3
3
3 3 3 3 0. 0. 0. 0.95 95 95 95 85 85 85 85 115 115 115 115 50 50 50 50 Regul. Regul. Regul. Regul. 218 218 218 218 214 214 214 214 286 286 286 286
Semi Semi Semi Semi----fast fast fast fast burner burner burner burner
Nr. 1 Nr. 1 Nr. 1 Nr. 1
1.
1. 1.
1.75
75 75
75 0
0 0
0....6
6 6
6 65
65 65
65 97
97 97
97 40
40 40
40 Regul.
Regul. Regul.
Regul. 127
127 127
127 125
125 125
125 167
167 167
167