Tecnimed VisioFocus LIGHT 06710 Скачать руководство пользователя страница 15

Страница: 15 / 18

Ambient temperature

(shown when in stand-by)

Measurement range: 5,0/45,0°C (41.0/113.0°F)

Accuracy: ±1.0°C (±1.8°F)

13.2 General specifications

- Power supply: 2 AAA (LR03) alkaline batteries - 1.5 V (included)

- Life of high quality batteries: up to 3 years or 30,000 readings (depending on use)

- Dimensions: mm 94,5 x 43,5 x 21,5 (3.72, 1.71, 0.85 inches)

- Weight: 60 gr. (2.12 oz.) - batteries included

- Distance from the subject: calculated using an optical aiming system (approx. 6

cm/2.36 inches).

- Expected life: 10 years.

- Atmospheric pressure range of operating conditions: from 700 hPa to 1,060 hPa.

- Relative humidity range of operating conditions: from 15% to 93%, non-condensing.

- Keep in a clean, dry place, preferably at a temperature ranging b16 and

+40°C (60.8 and 104°F). Store at a temperature not lower than -25°C (-13°F) or higher

than +70°C (158°F).

- Internally powered equipment; mode of operation: continuous.

- The VisioFocus LIGHT LEDs emit low light radiation in compliance with EN 62471.

- Measuring system tested in hospitals, private clinics and medical offices. Clinical

accuracy, characteristics and procedures are available from the manufacturer on re-

quest.

13.3 Declaration of Conformity UE

Tecnimed srl, P.le Cocchi, 12 - 21040 Vedano Olona (VA) - Italy is the manufacturer of

the VisioFocus LIGHT 06710 non-contact clinical infrared thermometer.

TECNIMED guarantees that VisioFocus LIGHT 06710 meets all the provisions appli-

cable in the Regulation (UE) 2017/745.

VisioFocus LIGHT 06710 is a class

a medical device manufactured following appro-

priate production processes in accordance with an EN ISO 9001:2015 and EN ISO

13485:2016 certified Quality System, with GMP requirements and with the following

standards: EN 60601-1, EN 60601-1-2, EN 60601-1-6, EN 60601-1-11, EN 62366,

EN 62471, EN 62304, EN 80601-2-56, ASTM E 1965-98.

Full responsibility for the conformance of this product to the standards is assumed by

Tecnimed srl, P.le Cocchi, 12 - 21040 Vedano Olona (VA) – ITALY.

Complete Declaration of Conformity is available from the manufacturer on request:

[email protected]

Содержание VisioFocus LIGHT 06710



















Результаты поиска

Содержание VisioFocus LIGHT 06710

Отзывы:

Похожие инструкции для VisioFocus LIGHT 06710

Бренды по названию

Популярные бренды

Tecnimed VisioFocus LIGHT 06710, Руководство по эксплуатации

Результаты поиска

Содержание VisioFocus LIGHT 06710

Отзывы:

Похожие инструкции для VisioFocus LIGHT 06710

Бренды по названию

Популярные бренды