manualshive.com logo in svg

Tecnibel CA250R5TA Series, Руководство по установке

Поделиться
Скачать
Tecnibel CA250R5TA Series Скачать руководство пользователя страница 25

24

EG

Activation of
protective
device

Thermistor failure

EEPROM of indor unit’s PCB is abnormal.

Fault with
compressor
and its circuit

P1

P2

P3

P4

P5

P6 ~ 8

P9

P10

P11 ~ 17

F1

F2

F3

F4

F6

F7

F8

F9

F29

H1

H2

H3

H4

H5

H6

H7

H8

H10

H11

H12

H13

H14

H15

H16

H17

H18

• Thermal protector in indoor fan motor is activated.

• Thermal protector in outdoor fan motor is activated.
• Compressor thermal protector is activated.
• Power supply voltage is abnormal (More than 260 V or less than 160 V

between L and N phase.)

Discharge gas temperature is abnormal.

High pressure switch is activated.

Power supply voltage is abnormal. Negative phase or defective phase.

–

Improper wiring connections of ceiling panel.

Float switch is activated.

–

Indoor coil temp. (E1 = TH1) cannot be detected.

Indoor coil temp. (E2 = TH2) cannot be detected.

Indoor coil temp. (E3 = TH3) cannot be detected.

Discharge gas temp. A (TH0A) cannot be detected.

Outdoor coil liquid temp. (C1 = TH0E) cannot be detected.

Outdoor coil gas temp. (C2 = TH0C) cannot be detected.

–

• Other thermistor is either open or damaged.

Compressor motor is overloaded.

Compressor motor is locked.

Compressor current detection circuit is abnormal.

–

–

Low pressure protector is activated (low pressure switch or low pressure prevention)

–

–

–

–

–

–

–

–

–

–

Compressor contactor (Mg SW) is chattering.

Protective device in indoor unit is
activated.

Protective device in outdoor unit is
activated.

Protective device in indoor unit is
activated.

Indoor thermistor is either open or
damaged.

Outdoor thermistor is either open 
or damaged.

Protective device for compressor
is activated.

Possible cause of trouble

Alarm

message

Main indoor unit address is not set. (Group control setting of indoor unit is abnormal.)

L1

Model setting of indoor unit is not matching the outdoor unit.

L2

When using group control, main indoor unit address setting is duplicated. (Judging by indoor unit.)

L3

Indoor unit address is duplicated.

L4

Priority setting of indoor unit is duplicated.

L5

–

L6

Improper wiring between indoor unit. (There is group connection wiring in case of individual control.)

L7

Indoor unit address (or group address) is not set.

L8

Capacity code of indoor unit is not set.

L9

Capacity code of outdoor unit is not set.

L10

Improper wiring of group control wiring.

L11

Model setting of indoor unit is not proper.

L13

Содержание CA250R5TA Series













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды