background image

 

 

 

 

 

 

 

 

 
 

 
 
 

 
 

SE-4048 

Tel

:021-22371482  

Fax

:021-66402031 

Www.techs.is  , [email protected] 

Page

11

 

 

elevation         

 

 

Products with this mark are only suitable for safe use in areas below 2000m above sea level. 
 

dustproof         

Dust falling on the surface of the switch can cause electrostatic adsorption and poor contact of the 
metal contacts. Although the device itself has made certain measures in anti-static, when the static 
electricity exceeds a certain intensity, it will still cause fatal damage to the electronic components on 
the internal circuit board. To avoid the static electricity affecting the normal operation of the device, 
please pay attention to the following: 

1.

 

Regular dust removal to keep indoor air clean; 

2.

 

Make sure that the equipment is well grounded to ensure the smooth transfer of static 
electricity. 

interference         

Electromagnetic interference will affect the electronic components such as capacitors and inductors 
inside the device by means of capacitive coupling, inductive coupling, impedance coupling, etc. To 
reduce the adverse effects caused by electromagnetic interference, please pay attention to the 
following: 

1.

 

The power supply system takes necessary measures against grid interference; 

2.

 

The switch should be away from high-frequency, high-power, high-current equipment, such 
as wireless transmitters; 

3.

 

Take electromagnetic shielding measures when necessary. 

lightning protection needs         

When a lightning strike occurs, a strong current is generated in an instant, and the air in the discharge 
path is instantaneously heated to 20,000 degrees Celsius, and an instantaneous large current is 
enough to cause fatal damage to the electronic device. For better lightning protection, please note the 
following: 

1.

 

Confirm that the rack is in good contact with the ground; 

2.

 

Make sure the power outlet is in good contact with the ground; 

3.

 

Reasonable wiring to avoid internal induction lightning; 

4.

 

When using outdoor wiring, it is recommended to use a signal lightning arrester. 

 
 

Содержание SE-4048

















Отзывы: