TechPlus ComfortAire Скачать руководство пользователя страница 35

Страница: 35 / 86

TechPlus

s e r v i c e

s u p p l e m e n t

Condenser Coil

Removal

1. Remove the refrigerant from the system.

2. Remove lines that are connected to the condenser and receiver driers.

3. Remove mounting bolts.

4. Drop condenser and remove the condenser grill.

5. Remove screws to casing, remove coil from casing.

Installation

1. Place the coil in the casing and install all mounting screws.

2. Install grill, set condenser unit in place and install mounting screws.

3. Install all lines and tighten fittings.

4. Replace receiver drier.

5. Pressurize system and check for leaks.

6. Evacuate and recharge with refrigerant.

Receiver Drier

Removal

1. Remove refrigerant from system

2. Remove lines from drier.

3. Remove bracket.

4. Remove HP Binary Switch set aside for re-use.

Installation

1. Install existing HP Binary switch you set aside in the previous step.

2. Install drier with new lubricated O Rings in place.

3. Tighten fittings to hoses.

4. Tighten drier bracket.

APPENDIX

c c

8 0

Содержание ComfortAire























































































Результаты поиска

Содержание ComfortAire

Отзывы:

Бренды по названию

Популярные бренды

TechPlus ComfortAire, Руководство по дополнительному обслуживанию

Результаты поиска

Содержание ComfortAire

Отзывы:

Бренды по названию

Популярные бренды