background image

DP-PSUEN EN54-4 Fire Alarm Power Supply Series 

– INSTALLATION & OPERATION MANUAL 

 

 
DP-PSUEN Series Installation & Operation Manual Rev 11.1 220323.docx 

E&OE 

- 7 - 

4.3

 

PRINTED CIRCUIT BOARD 

All three power supplies have a very similar form, fit and function, the dimensions are identical. The DP-PSUEN5 is 
shown as an example below. 

NOTE

:  Plastic cage is not fitted on the DP-PSUEN5 power supply: 

168.00

141

.00

145.00

6.00

10.00

7.00

129

.50

6

.00

5

.50

Power DC status LED, yellow:  Indicates 

that DC power is available

AC OK led, green:  Indicates 

availability of external AC power 

Battery Fault, yellow:  Indicates 

if any battery faults are present 

PSU Fault, yellow:  Indicates 

any power supply system faults 

are present 

Battery 
Connectors

Nominal 24V 
output 2 to load

Nominal 24V 
output 1 to load

3.2mm Mounting Holes x 5

Live AC power connection

Case and earth connection tab

Protective earth connection

Neutral AC power connection

SW1 and SW2 control inputs 
inversion jumper

Battery-free operation jumper

Optional external temperature 
sensor connector

On-board temperature sensor 
disable jumper

24V output switching control 
inputs with 0V return

External Power Supply (AC power) 

fault normally closed relay output

Serial data interface 

External LED interface

Auxiliary Power Supply (battery) 

fault normally closed relay output

Power Supply fault normally 

closed relay output

Plastic safety cage

 

5

 

INSTALLATION AND OPERATION 

NB:

 

WARNING: Isolate the AC power supply before working on the power supply. Only suitably qualified 
personnel should install these power supplies and wiring should comply with the latest edition of IEE 
Wiring Regulations (BS 7671) or local national electrical standards. 

5.1

 

MOUNTING 

The power supplies are designed for indoor use, within the specified operational temperature and humidity limits. 

The metal enclosures should be mounted on a solid, flat and dry surface using the three mounting points provided. 
The screws should have a minimum shank diameter of 5mm (No 11 gauge) and use suitable wall plugs where 
needed.  

Содержание DP-PSUEN Series















Отзывы: