Technisonic Industries Limited TFM-530 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 42

Technisonic Industries Limited TFM-530 Скачать руководство пользователя страница 19

3-1

SECTION 3

INSTALLATION INSTRUCTIONS

3.1

GENERAL

This section contains information and instructions for the correct installation of the TFM-530,
VHF/FM Transceiver. Make certain that the correct frequencies are preprogrammed in accordance

with the equipment user's valid FCC operator's license, prior to installation.

3.2

EQUIPMENT PACKING LOG

Unpack the equipment and check for any damage that may have occurred during transit. Save the
original shipping container for returns due to damage or warranty claims. Check that each item on

the packing slip has been shipped in the container. Verify that the equipment display and backlighting
configuration are the same as those ordered.

3.3

TRANSCEIVER

INSTALLATION

The TFM-530 transceiver is designed to be Dzus mounted and should be installed in conjunction with

a IN-550 installation kit. See Figure 3-1 for an outline drawing of the unit with dimensions to facilitate

the installation.

3.4

INSTALLATION KIT - CONTENTS

The IN-550 installation kit consists of:

1. One 15 pin Cannon D mating connector (female) complete with crimp pins and hood.

2. One 9 pin Cannon D mating connector (male) complete with crimp pins and hood.

3. Three BNC antenna mating RF connectors (male).

3.5

ANTENNA

INSTALLATION

Antenna, Comant P/N CI-292-3 or suitable equivalent may be utilized for VHF and the Foxtronics
model FLX-3050B antenna/tuning system or Sensor Systems P/N S65-8282-34 may be utilized for

the VLO band. A suitable whip antenna cut for a specific VLO frequency may also be used. The

antenna should be mounted on the bottom of the aircraft whenever possible and must be located at

least 20 cm (8inches) from any occupant in the airframe. Consult with instructions provided with the

antennas. Connect RF cables from antennas to the back of the TFM-530 unit by utilizing the BNC

connectors provided in the installation kit. The VLO connector is located on the rear, above the 15-pin
D connector and the VHF connector is below the 9-pin D.

3.6

INSTALLATION - PIN LOCATIONS AND CONNECTIONS

The pin numbers and locations for the 15 pin and 9 pin Cannon D located on the rear of the TFM-530

transceiver are shown below. Pin connections are in provided in TABLE 3-1.

Transceiver mounted view of 15 pin female and 9 pin male connector

«
...
17
18
19
20
21
...
»

Содержание TFM-530











































Отзывы:

Нет отзывов