Technisonic Industries Limited TBS-150/8.33 Скачать руководство пользователя страница 47

Страница: 47 / 47

3-23

3.5.4

Switching OFF

To switch off the transceiver:

(1)

Set the POWER ON/OFF on transceiver to switch to OFF.

(2)

Verify that all indicator LED's on the front panel are OFF.

NOTE

When the transceiver is switched OFF there is no
current drain from external DC.

3.5.5

Battery Charging

(1)

Set AC ON/OFF switch to OFF.

(2)

Install External DC Power Cable P/N 863701-1 (Not Supplied) or equivalent to DC
Connector on rear of Panel. Connect to batteries to be charged.

(3)

Set AC ON/OFF switch to ON.

3.5.6

External DC Operation

(1)

Set AC ON/OFF switch to OFF.

(2)

Install External DC Power Cable P/N 863701-1 (Not Supplied) or equivalent to DC
Connector on rear of Panel. Connect to External DC Source.

NOTE

Ensure that the DC source voltage does not exceed
30 Vdc. The 15 watt and 25 watt units can operate
within the range 21.6 Vdc to 30 Vdc. The 7 watt units
can operate within the range of 11.5 Vdc to 15 Vdc.

Содержание TBS-150/8.33
















































Результаты поиска

Содержание TBS-150/8.33

Отзывы:

Бренды по названию

Популярные бренды

Technisonic Industries Limited TBS-150/8.33, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TBS-150/8.33

Отзывы:

Бренды по названию

Популярные бренды