TechnipFMC Smith Meter Genesis Series Скачать руководство пользователя страница 17

Страница: 17 / 20

Issue/Rev. 0.0 (10/18)

MN01047

•

Page 17

Figure 45 – Fully Assembled Meter

The Locking Screw will need to be tightened. This locks

the Rotor and Blade Assembly to the Housing (Figure 44).
Do not push in while tightening or the rotor may bind on

the cover.

Tighten the Locking Screw to the following Torque Values:

2" – 150 in/lb (17 N

•

3" – 250 in/lb (29 N

•

Note:

The Locking Screw needs to be tightened after the Cover is

installed.

Figure 44 – Install Locking Screw

Locking Screw

Install the Locking Screw Pipe Plug.

Now the meter is fully assembled. Insert a soft tip

tool into the meter inlet and spin the Rotor and Blade

Assembly. There should be no binding and it should

operate smoothly.

Section IV – Assembly (continued)

Содержание Smith Meter Genesis Series





















Результаты поиска

Содержание Smith Meter Genesis Series

Отзывы:

Похожие инструкции для Smith Meter Genesis Series

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter Genesis Series, Руководство по обслуживанию

Результаты поиска

Содержание Smith Meter Genesis Series

Отзывы:

Похожие инструкции для Smith Meter Genesis Series

Бренды по названию

Популярные бренды