background image

Routine maintenance

 

Have the condition and efficiency of the gas pipe and the pressure 
regulator (if installed) checked periodically. If anomalies are found, 
do not repair components but have the faulty component replaced. 
To ensure good performance and safety, the gas regulator taps 
must be greased periodically. 

Periodic lubrication of the taps and any other appliance service 
must only be carried out by Authorised Personnel. 

Abnormal operation

Any of the following are considered to be abnormal operation and 
may require servicing:

·

Yellow tipping of the burner flame.

·

Sooting up of cooking utensils.

·

Burners not igniting properly.

·

Burners failing to remain alight.

·

Burners extinguished by cupboard doors.

·

Gas valves, which are difficult to turn.

Please read the troubleshooting tips on page 25 before contacting 
Technika.

Service and parts

 

Before leaving the factory, this appliance was tested and adjusted 
by specialist skilled staff to give the best operating results. Any 
subsequent necessary repairs or adjustments must be carried out 
with the greatest care and attention by authorised personnel. For 
this reason, we strongly advise you contact the Technika Service 
Center, specifying the nature of the problem, the model of the 
equipment and the serial number. This data is provided on the 
data label adhered to the base of the appliance and on the 
duplicate data label. Always use original Technika spare parts. 

Warranty 

Your new appliance is covered by a warranty. The details of your 
warranty conditions are on your Warranty Card supplied with the 
appliance. Keep the physical receipt which documents your 
purchase of the appliance and purchase date as you will need to 
show this for any Warranty repairs. Warranty cannot be claimed 
without proof of purchase.  When the appliance has been provided 
by a builder, the certificate of occupancy is acceptable as proof of 
purchase.

14

Use and Care

Содержание TGC6G Series





























Отзывы: