background image

6. CHECKING ELECTRICAL COMPONENTS

6-1 Measurement of Insulation

Resistance

The insulation is in good condition if the 
resistance exceeds 2M

Ω 

6-1-1. Power supply wires

Clamp the grounding terminal of the power plug
with a lead clip of the insulation resistance tester
and measure the resistance by placing a probe 
on both the two power terminals. (fig.1)

Then, also measure the resistance between the
grounding and other power terminals. (fig.1)

6-1-2. Indoor Unit

Clamp a metallic part of the unit with the lead
clip of the insulation resistance tester and measure
the resistance by placing a probe on each terminal
screw where power supply lines are connected on the
terminal plate. (fig.2)

6-1-3. Outdoor Unit

Clamp an aluminium plate fin or copper tube with
the lead clip of the insulation resistance tester
and measure the resistance by placing a probe
on each terminal screw on the terminal plate. (fig.2)
Note that the ground line terminal should be skipped
for the check.

6-1-4. Measurement of Insulation

Resistance for Electrical Parts

Disconnect the lead wires of the desired electric
part from terminal plate, capacitor, etc.
Similary disconnect the connector.
Then measure the insulation resistance. (fig.3 and 4)

NOTE: Refer to electric wiring diagram

If the probe cannot enter the poles because the
hole is too narrow then use a probe with a
thinner pin.

Ground

power plug
(Local supply)

probe

Insulation
tester

Terminal plate

Copper
tube or
metallic part

Clip

Insulation
tester

Probe

Copper
tube or
metallic part

Clip

Insulation
tester

Probe

Clip

Insulation
tester

Probe

Metallic
part

From fan motor,
compressor and
other parts

Fig. 2

Fig. 3

Fig. 4

The shape of the power plug may differ from that

of the air conditioner which you are servicing.

NOTE

Fig. 1

29

Содержание 387106985
































Отзывы: