TEC MA-600-1 series Скачать руководство пользователя страница 79

Страница: 79 / 188

12. JOURNAL AND RECEIPT PAPER-END DETECTOR

EO1-11155

12. JOURNAL AND RECEIPT PAPER-END DETECTOR

12- 1

12. JOURNAL AND RECEIPT PAPER-END DETECTOR

(1) This detects when either the journal or receipt paper is coming near the end. It is provided in order to prompt

the operator to replace the old paper roll with a new one.

(2) When the paper roll is out (or the paper has not been set properly), no key operation will be accepted and the

front display will indicate “PAPER END”.

(3) When a new paper roll is set, only the [C] key is allowed to operate. The error message “PAPER END” will be

cleared by the [C] key depression and normal key-in operations will be accepted. If any printing was
suspended, it will continue printing.

(4) If this detector senses a paper-end condition during printing, the printing will stop after the current line printing

is completed.

(5) If the [C] key is depressed in the paper-end condition, it will be ignored. The [C] key depression will be

effective to clear the error message only after the new paper roll is set.

(For further details, refer to Chapter 6.)

Receipt paper end

Journal paper end

P blinks on the leftmost digit of the
10-digit 7-segment Numeric display.

P blinks on the third leftmost digit of the
10-digit 7-segment Numeric display.

Содержание MA-600-1 series





























































































































































































Результаты поиска

Содержание MA-600-1 series

Отзывы:

Похожие инструкции для MA-600-1 series

Бренды по названию

Популярные бренды

TEC MA-600-1 series, Руководство пользователя

Результаты поиска

Содержание MA-600-1 series

Отзывы:

Похожие инструкции для MA-600-1 series

Бренды по названию

Популярные бренды