background image

To make this  adjustment release the lever from the brake 
actuator, slacken the clamp bolt and remove the lever from 
the cam shaft spline. Turn the lever 1 or more teeth of the 
spline towards the actuator. The cam shaft may need to be 
rotated in the opposite direction to align the splines.  Slide 
the lever back onto the shaft.

 

Reconnect the brake lever to the brake actuator and make 
sure that the brake shoes are not in contact with the drum, 
and the wheel can rotate freely.

 

IMPORTANT: 

The pivot point of the actuator on the lever 

must  not  be  altered  without  the  permission  of  the  vehicle 
manufacturer  because  this  will  change  the  braking 
efficiency of the vehicle. The factory set position is listed in 
the table below.

 

Table 10.  Brake actuator position on brake lever.

 

13.22.2 Adjusting Brake Levers  

-

 Adjustable lever.

 

Safely  raise  the  vehicle  as  described  in  section  13.14. 
Adjust  the  position  of  the  lever  by  rotating  the  screw 
clockwise  when  the  brakes  are  not  applied  (Figure  19). 
Adjust  the  lever  to  the  closest  possible  setting  that  still 
allows the  wheel to turn freely.  Apply grease to the  lever 
using the grease nipple provided.

 

Figure 19.  Brake adjustment screw.

 

13.23 Pneumatic Brakes

 

The  two

-

line  trailer  braking  system  which  is  fitted  to  this 

machine  uses  one  Red  air  line  (known  as  a  supply  or 
emergency  line)  which,  when  coupled  to  the  tractor  is 
permanently pressurised,  and one  Yellow line (known as 
the service or control line) which has a variable pressure. 

 

This  variable  pressure  is  controlled  by  the  tractor,  and  is 
determined  by  the  force  on  the  brake  pedal  or  whether 
the tractor’s parking brake is applied. 

 

It  is  commonplace  for  this  line  to  be  fully  pressurised 
when the tractors ignition is switched OFF. 

 

13.23.1  Connector Filters

 

The  air  enters  the  trailer  via  the  red  and  yellow  flexible 
connection  lines,  and  passes  through  a  filter  in  each  line. 

The filters are designed to trap particles of dirt, and to stop 
them  entering  the  system,  they  are  not  designed  to  stop 
water entering the system. 

 

Filters  should  be  dismantled  and  cleaned  from  time  to 
time to remove any debris. 

 

13.23.2  Air reservoir 

 

To  remove  any  water  that  has  condensed  in  the  air 
reservoir it should be drained daily. 

 

A drain valve is fitted at the bottom of each air reservoir. 

 

13.23.3  Trailer control valve

 

The trailer control valve has several functions, one of which 
is load sensing. 

 

CAUTION: 

The  Tomahawk  has  3  pre

-

set  brake 

settings (laden, part laden and empty) as the machine 

does not  have suspension.  The  linkage is  pre

-

set  to  give 

the correct brake performance and should not be adjusted.

 

Oil the pivot points. 

 

13.23.4  Air lines

 

Inspect regularly for leaks.

 

13.24 Lubrication

 

Good  quality  semi

-

solid  grease  should  be  applied  to  the 

grease points as shown on the relevant lubrication chart on 
pages 2  to 5.

 

The frequencies stated are based on typical daily use for 
bedding & feeding purposes.  Continuous use for special 
applications will necessitate more frequent lubrication.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjustment 

Screw

 

29

 

Brake Size 

mm

 

Lever Length

 

Hydraulic Brakes

 

Lever Length

 

Air Brakes

 

300 x 60

 

120 mm

 

N/A

 

406 x 120

 

N/A

 

127 mm

 

Model

 

9500

 

9500

 

1010

 

300 x 60

 

120 mm

 

N/A

 

1010

 

406 x 120

 

N/A

 

152 mm

 

Содержание Tomahawk 1010









































Отзывы: