background image

408-4228

5 of 6

Rev C

8. MAINTENANCE

Ensure that the tool and dies are clean by wiping them 
with a clean, soft cloth. Remove any debris with a 
clean, soft brush. Do not use objects that could 
damage the tool. When not in use, keep handles 
closed to prevent objects from becoming lodged in the 
crimping dies, and store in a clean, dry area.

9. VISUAL INSPECTION

The crimping dies should be inspected on a regular 
basis to ensure that they have not become worn or 
damaged. Inspect the crimp sections for flattened, 
chipped, worn, or broken areas. If damage or 
abnormal wear is evident, the tool must be replaced. 
See Section 10, REPLACEMENT.

10. REPLACEMENT

Customer-replaceable parts are shown in Figure 1.

Available separately, PRO-CRIMPER III Hand 
Crimping Tool Repair Kit 679221-1 includes a 
replacement nut and a variety of pins, rings, screws, 
and springs. 

If the dies are damaged or worn excessively, they 
must be replaced.

Order the repair kit and replaceable parts through your 
TE representative, or call 1-800-526-5142, or send a 
facsimile of your purchase order to 1-717-986-7605, or 
write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

11. REVISION SUMMARYSINCE

Since this sheet was revised, the new company logo 
has been applied.

Содержание PRO-CRIMPER III







Отзывы: