background image

408- 1559

9

of 10

Rev

T

2. Position the product in the crimping chamber

according to Paragraph 3.1, Steps 1 through 5 or

Paragraph 3.2, Steps 1 through 6.

3. While holding the wire in place, squeeze the tool

handles together until the ratchet releases. Holding

the tool in this position, maintain just enough

pressure to keep the jaws closed.

4. Check the clearance between the bottoming

surfaces of the jaws. If the clearance is .025 mm

[.001 in.] or less, the ratchet is satisfactory. If

clearance exceeds .025 mm [.001 in.], the ratchet

is out of adjustment and must be repaired. Refer to

Section 6, REPLACEMENT AND REPAIR. If the

tool conforms to this inspection procedure,

lubricate it with a THIN coat of any good SAE 20

motor oil, and return it to service.

6. REPLACEMENT AND REPAIR

Customer--replaceable parts are listed in Figure 10.

A complete inventory should be stocked and

controlled to prevent lost time when replacement of

parts is necessary. Parts other than those listed

should be replaced by TE to ensure quality and

reliability. Order replacement parts through your

representative, or call 1--800--526--5142, or send a

facsimile of your purchase order to 717--986--7605, or

write to:

CUSTOMER SERVICE (038--035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105--3608

For customer repair service, call 1--800--526--5136.

7. REVISION SUMMARY

Revisions to this instruction sheet include:

S

Updated document to corporate requirements.

S

Added tool number 68343--1.

Содержание CERTI- CRIMP Series











Отзывы: