TDK-Lambda PYH200 Series Скачать руководство пользователя страница 3

PYH200 Manual

 

DC-DC Converter Isolated, 200W, ½ Brick, PCB Mount 

 

4.  I

NSTALLATION 

I

NSTRUCTIONS

 

Before operating this device, please read this manual thoroughly and retain for future reference! This device 

may only be installed and put into operation by qualified personnel. If damage or malfunction should occur 

during operation, immediately turn power off and send device to the factory for inspection. The device does 
not contain serviceable parts.  
 

WARNING

  Risk of electrical shock, fire, personal injury or death. 

Turn power off before working on the device. Protect against inadvertent re-powering. 
Do not modify or repair the unit. 
Do not open the unit as high voltages are present inside. 
Use caution to prevent any foreign objects from entering the housing. 
Do not use in locations where flammable gas or ignitable substances are present. 
Do not use in wet locations or in areas where moisture or condensation can be expected. 
Do not use in environment with strong electromagnetic field, corrosive gas or conductive substances or direct 

sunlight. 
Do not touch during power-on, and immediately after power-off. Hot surfaces may cause burns. 

Obey the following installation instructions:

 

This device may only be installed and put into operation by qualified personnel. 
This device does not contain serviceable parts. Replace fuses only when explicitly permitted. If damage or 

malfunction should occur during installation or operation, immediately turn power off and send unit to the 

factory for inspection. 
Install the device in an enclosure providing protection against electrical, mechanical and fire hazards. 
The device is designed for pollution degree 2 areas in controlled environments. No condensation or frost is 

allowed. 
The input can be powered from batteries or similar DC sources. 
Check for correct input polarity. The device will get damaged when the voltage is reversed. 
Ensure sufficient cooling to avoid overloading the device. 
The device is designed for altitudes up to 5000m (16400ft). 
This device is not internally fused. An external input fuse must always be used. Use a 25A slow-blow fuse. 
The maximum operational case temperature is +100°C (+212°F). The case temperature is defined in the 

middle of the top side of the cover. 
The device is designed to operate in areas with a maximum relative humidity of 95%. 
Do not apply return voltages from the load to the output terminals. 
Do not connect the outputs of multiple devices in parallel for higher output currents. 
Do not connect batteries for charging purposes to the output of the device. 

All parameters are typical values specified at nominal input voltage, nominal output load, 25°C ambient and after a 5 minutes run-in time unless  
otherwise noted. The information presented in this document is believed to be accurate and reliable and may change without notice. 

For additional information, please visit https://product.tdk.com/info/en/products/power/index.html 

3/21

DOC-ID: IM-PYH200-2022-05-04

 

Содержание PYH200 Series






















Отзывы: