TC Electronic UpCon Скачать руководство пользователя

Страница: 49 / 114

Obtaining UpCon status information

UpCon English Manual (2014-10-07) 46

Please note that the LEDs on the front of a Up-
Con will display basic status information as long
as the device is powered – see “Front panel indi-
cators” on page 24.

Additional status information can be obtained
using TC Icon, where you can also define how
certain error states should be indicated on the
device.

To display status information about UpCon, go to
Frame / System / Status.

Fig. 24.: UpCon (SDI) Status page

This page will display the following status infor-
mation:

Clock section

Source indicator

Indicates the source of the clock signal UpCon is
currently following.

Lock indicator

Indicates wether synchronization has been
achieved. If no synchronization has been
achieved, a red LED will be shown in this field.

Nominal Rate indicator

Shows the detected sample rate of the signal
UpCon is synced to.

Status section

Power indicator

Displays the current state of the UpCon power
supplies.

A power supply failure may be indicated as de-
scribed under “Power Warning parameter” on
page 46.

Power Warning parameter

A failing supply is

always

indicated by a red LED

on the front panel of the device. TC Icon can also
indicate a failing power supply, depending on the
setting of the “Power Warning” parameter.

“Off” setting

A failing power supply is not reported in the Icon
remote app.

“Warning” setting

A failing power supply is indicated by a

yellow

“Power” label in the respective UpCon Frame in-
dicator, and a yellow LED will be shown on the
Frame tab when it is selected.

“Error” setting

A failing power supply is indicated by a

red

“Power” label in the respective UpCon Frame
indicator, and a red LED will be shown on the
Frame tab when it is selected.

Содержание UpCon



















































































































Результаты поиска

Содержание UpCon

Отзывы:

Похожие инструкции для UpCon

Бренды по названию

Популярные бренды

TC Electronic UpCon, Руководство пользователя

Результаты поиска

Содержание UpCon

Отзывы:

Похожие инструкции для UpCon

Бренды по названию

Популярные бренды