TC Electronic PowerCore CL, Руководство пользователя

Страница: 5 / 7

OPERATING TIPS
8
O OP PE ER RA AT TIIN NG G M ME ET TH HO OD DS S
To adjust the value of a control, click on the knob or the numerical display and move the
mouse in the directions that are indicated by the mouse cursor. To reset a control to its
default value, hold the [Option] key and click on the control. Double-clicking on a value
field will bring up a dialog for numeric entry.
M ME ET TE ER RIIN NG G
C Clliip p IIn nd diicca atto orr
With more than three consecutive clips the number above the meter will turn RED
indicating that clipping has occurred. To release this condition; click on the number.
M Me ette errss
The LED meters indicate PPM values. With its fast rise time and relatively slow fallback
time, PPM metering is excellent for reading fast, transient sounds and will allow much
better detection of clips compared to RMS metering.
IIn n//O Ou utt S Sw wiittcch h
Switches Meter indication between input and output signal (only in stereo mode).
P Pe ea ak k H Ho olld d O Op pttiio on nss
Click on the meter to get a pop-up with Peak Hold options – you can select between
infinite peak hold and a hold time of 6 seconds.
G Ga aiin n R Re ed du uccttiio on n M Me ette err
In the Compressor section, there is an accurate gain reduction meter. The further down
the series of LEDs the meter moves, the more gain you are losing by the compression
process.
L Liim miittiin ng g M Me ette err
In the Limiter section, there is a limiting meter. This LED Meter gives
feedback of the applied limiting. The more LEDs that light up, the more limiting
is applied to the signal.
9
C CO OM MP PR RE ES SS SO OR R P PA AR RA AM ME ET TE ER RS S
C Co om mp prre esssso orr -- The button enables and disables the compressor section. The section is
displayed in blue when active, and grayed out when disabled.
T Th hrre essh ho olld d -- Sets the level threshold at which the compressor starts working
(0 dB to -40 dB).
R Ra attiio o -- Sets the amount of the compression ratio (1.0:1 to infinite).
A Atttta acck k -- Compression attack time setting in milliseconds (0.2 ms to 50 ms).
R Re elle ea asse e -- Compression release time setting in milliseconds (10 ms to 1.0 second).
O Ou uttp pu utt -- Output Gain of the Compression stage (-10 dB to +30 dB)
H Ha arrd d K Kn ne ee e//S So offtt K Kn ne ee e -- Switches the compressor between Hardknee and Softknee
compression.
L LIIM MIIT TE ER R P PA AR RA AM ME ET TE ER RS S
L Liim miitte err -- Limiter - The button enables and disables the limiter section. The section is
displayed in yellow when active, and grayed out when disabled.
T Th hrre essh ho olld d -- Sets the limiter’s threshold in decibels (dB) (0 dB to -12 dB).
R Re elle ea asse e -- The limiter’s release time setting in milliseconds (10ms to 1 second).
S So offttS Sa att O On n//O Offff -- This switch enables and disables SoftSat. SoftSat creates that warm
analog sound associated with classic studio equipment.
S So offttS Sa att -- Sets the amount of saturation in decibels (dB) (-6 dB to +3 dB).
S So offtt C Clliip p -- When the Soft Clip LED becomes active, soft clipping has been engaged in the
limiter. When a digital signal begins to clip, the wave form becomes square. Soft clipping
rounds off the edges of the clipped wave form, making the sound easier to listen to.
C Ce eiilliin ng g - The ceiling parameter sets the absolute max output for the Limiter.
PARAMETERS