TC3005
(LED/ELED/LASER)
User's Manual
Rev. 3.0
−1−
1.
1.
1.
1.
1.
Description
Description
Description
Description
Description
The TC3005 gives users the ability to convert Multimode fiber optic signals to Single Mode format for data
transmission (and vice-versa). These conversions can benefit users by extending transmission distances
and/or enabling dissimilar fiber optic devices to be used with different fiber types. The optic receiver detects
the incoming optical signal and regenerates it for transmission through the second optic transmitter. The
TC3005 is available in multiple configurations depending on your communication requirements. When both
sides have the same wavelength, the TC3005 works like an optical signal repeater.
2.
2.
2.
2.
2.
Data Rates
Data Rates
Data Rates
Data Rates
Data Rates
165Mbps*
*Contact factory for higher data rates.
3.
3.
3.
3.
3.
Optical Specifications
Optical Specifications
Optical Specifications
Optical Specifications
Optical Specifications
Transmitter:
Transmitter:
Transmitter:
Transmitter:
Transmitter:
LED; typical Launch Power:
-16 dBm* (850nm/1310nm, Multimode @62.5/125µm)
ELED; typical Launch Power:
-16 dBm* (1310nm/1550nm, Single Mode @9/125µm)
LASER; typical Launch Power:
-6 dBm* (1310nm/1550nm, Single Mode @9/125µm)
Receiver:
Receiver:
Receiver:
Receiver:
Receiver:
PIN DIODE; typical Sensitivity:
-33 dBm* (850nm/1310nm, Multimode @62.5/125µm)
-33 dBm* (1310nm/1550nm, Single Mode @9/125µm)
-36 dBm* (1310nm/1550nm, Single Mode @9/125µm)
Loss Budget:
Loss Budget:
Loss Budget:
Loss Budget:
Loss Budget: LED; 850nm/1310nm, MM @62.5/125µm
16 dB
ELED; 1310nm/1550nm, SM @9/125µm
16 dB
LASER; 1310nm/1550nm, SM @9/125µm
25 dB
Distance:
Distance:
Distance:
Distance:
Distance:
850nm, Multimode @62.5/125µm
up to 3km*
1310nm, Multimode @62.5/125µm up to 4km*
1310nm, Single Mode @9/125µm up to 40km*
1550nm, Single Mode @9/125µm up to 110km*
Wavelength:
Wavelength:
Wavelength:
Wavelength:
Wavelength:
Note: Any two wavelength combinations are available on each unit.
850nm Multimode (LED)
1310nm Multimode (LED)
1310nm Single Mode (ELED/LASER)
1550nm Single Mode (ELED/LASER)
Connector:
Connector:
Connector:
Connector:
Connector:
ST, FC, or SC
*Launch power, sensitivity and distance are listed for reference only. These numbers may vary. Contact
factory for higher loss budgets.
© COPYRIGHT 1992-2010. ALL RIGHTS RESERVED.
TC Communications, Inc. 17881 Cartwright Road - Irvine, CA 92614
Tel: (949) 852-1972 Fax: (949) 852-1948 Web Site: www.tccomm.com Email: [email protected]
4.
4.
4.
4.
4.
Power Requirements
Power Requirements
Power Requirements
Power Requirements
Power Requirements
A.
The TC3005 consumes very low power. The connector is a terminal block with polarity indicated on the
rear panel of the unit (see Figure 2). The input voltage is typically 12 VDC and current is @600mA. The
unit can be ordered with optional power options: 24 VDC@300mA, 48 VDC@150mA, or 115/230 VAC
with an external power adapter.
B .
Should an external power adapter need to be replaced, use one that matches the above specifications.
You may order it from TC Communications.
C.
There are two pairs of terminal block connectors on the rear panel (labeled "PWR A" and "PWR B").
Only one pair is required to power the unit. If both pairs are connected, the built-in power redundancy
feature will be utilized. When this feature is utilized, both "A" and "B" share the load. If one power source
fails, the other will assume the full load.
165Mbps Fiber Optic Mode Converter/Repeater
165Mbps Fiber Optic Mode Converter/Repeater
165Mbps Fiber Optic Mode Converter/Repeater
165Mbps Fiber Optic Mode Converter/Repeater
165Mbps Fiber Optic Mode Converter/Repeater
TC3005(LED/ELED/LASER)
TC3005(LED/ELED/LASER)
TC3005(LED/ELED/LASER)
TC3005(LED/ELED/LASER)
TC3005(LED/ELED/LASER)
User's Manual
User's Manual
User's Manual
User's Manual
User's Manual
