background image

Model LR-26C, LR-623, LR-28A, & LR-2355 Hoist Installation and Operation Manual 
Stock No. 036268 
Page 15 of 27 
 

"BODY PROP" 

NOTE: 

In order to comply with paragraph 10 of Federal Regulation #1926.601, all TBEI-
Rugby hoists will be sold with one body prop.  It is the responsibility of the installer to 
determine whether one body prop is sufficient.  The following information will help in 
making that determination. 

 

The body prop is designed for use only when the body is empty.  The purpose of the 
body prop is to hold an empty body in the raised position when performing 
maintenance or inspection on the hoist, body, or any component that requires working 
under an 

empty

 body. 

 

Some applications may require 2 or more body props to support the 

empty

 body.  To 

determine how many body props your application requires, refer to the following 
information. 

 

WARNING:

  Being under a raised body can result in serious injury or death should the body 

inadvertently descend.  

Never

 position yourself or allow others to position themselves 

under a 

loaded

 body.  

Always

 prop the 

unloaded

 body up using the body prop/s 

supplied.  

Remember

, body props are to be used only on an 

unloaded

 body.  When 

two props are provided, both props must be used. 

 

WARNING:

  Do not use body prop to support a loaded body! 

 

WARNING:

  Do not perform maintenance under a raised body without first blocking the empty body 

up with the body prop/s. 

 

WARNING:

  Do not use a body prop that is bent or otherwise damaged.  A damaged body prop will 

have a reduced holding capacity, and may break when used to hold up the body.  This 
could cause serious injury or death.  Replace a damaged body prop before using it. 

 

WARNING:

  Be sure to install the body prop according to the 

“INSTALLATION OF BODY 

PROP”

 section of this manual. 

 
The following is a step by step procedure to determine how many body props are required for this 
application. 
 
1. 

The TBEI-Rugby Part Number 03 0703 body prop is to be used with this hoist.  Determine if 

this is the body prop you have by referring to Figure 8. 
 
2. 

Determine the "P" value referring to Figure 9. The "P" value is the horizontal distance between 

the rear hinge and the prop. 
 

 

Содержание Rugby LR-26C




























Отзывы: