background image

64

Case Dimensions

Case Mounting

Drive Mounting

Terminals

Model

L

W

H

A

B

Size

X

Y

Size Lines GND

WLF40050D 14.17/360 9.17/233 4.09/104

13.54/

7.09/

Key-slot (top):

11.02/

7.87/

M6

AWG 6

M8

344

180

0.71/18/high

280

200

0.51/13/large diam.

0.26/6.5/small diam.

Slot (bottom):

1.04/26.5/depth

0.26/6.5/width

0.43/11/diam. of curve

WLF40200D 19.45/494 9.17/233 4.09/104

18.82/

7.09/

Key-slot (top):

16.54/

7.87/

M6

AWG 6

M8

478

180

0.71/18/high

420

200

0.51/13/large diam.

0.26/6.5/small diam.

Slot (bottom):

1.04/26.5/depth

0.26/6.5/width

0.43/11/diam. of curve

IP54 versions - up to 20HP

Notes:

1. Dimensions - inches / millimeters
2. The IP54 filters have a terminal block for line termination.  Use the indicated wire size.  The filter is 

connected to the inverter via the captive filter output cable.  Connect the leads to the inverter’s L1, L2, 
and L3 terminals.  Connect the ground lead to the inverter ground.

Figure 4

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание WFC1000 Series



















































































Отзывы: